Amana PTH153G50AXXX 目录
MC-DPTAC
www.amana-ptac.com
13
a
ccessories
(
conT
.)
WEMR01W
Recess-mounted door switch
WEMS01B
Surface-mounted door switch (Brown)
WEMS01W
Surface-mounted door switch (White)
W
iRed
e
neRgy
m
anagement
C
ontRol
Includes PIR occupancy sensor power from the DigiSmart control and door
switch; cannot be used with a remote wired thermostat.
switch; cannot be used with a remote wired thermostat.
SECM1001A
Climate Master 12½” Sleeve
Extension (10 Pack)
Extension (10 Pack)
SEZA0501A
Zone Aire 11½” Sleeve
Extension (5 Pack)
Extension (5 Pack)
W
all
S
leeve
e
xtenSion
a
daPteR
K
itS
Room-side extension kits to increase the depth of the existing sleeve to allow for
an industry-standard PTAC to be installed.
an industry-standard PTAC to be installed.
PTCB10B
10 Pack for R-22 units
PTCB10E
10 Pack for R-410A units
C
uRtain
b
affle
K
it
The color-matched polymer curtain baffles help to prevent curtains from falling
into the discharge air stream and causing recirculation, reducing efficiencies
and shortening compressor life.
into the discharge air stream and causing recirculation, reducing efficiencies
and shortening compressor life.
i
nTake
a
ir
f
ilTers
It is extremely important to clean the inlet air filters once a month (or more often if operated in dusty or dirty locations or
conditions) to properly maintain the operational performance of the PTAC unit. The two intake air filters (constructed of durable
polypropylene) can be easily inserted into the cabinet front using the cabinet filter guides. Before cleaning the intake filters, turn
the unit off by setting the mode switch to the OFF position. Filters should be cleaned as required.The following procedure is used
to remove the intake filters:
1. Facing the unit, pull up on the filter handles located at the front top of the unit.
2. Pull each filter upward and remove.
3. Clean filters with vacuum or with running water. Reverse this procedure to reinstall the filters.
conditions) to properly maintain the operational performance of the PTAC unit. The two intake air filters (constructed of durable
polypropylene) can be easily inserted into the cabinet front using the cabinet filter guides. Before cleaning the intake filters, turn
the unit off by setting the mode switch to the OFF position. Filters should be cleaned as required.The following procedure is used
to remove the intake filters:
1. Facing the unit, pull up on the filter handles located at the front top of the unit.
2. Pull each filter upward and remove.
3. Clean filters with vacuum or with running water. Reverse this procedure to reinstall the filters.
Note: Accessory filter kits are available from your sales person. All filters are permanent and cleanable. Consult your
I&O Manual for other monthly cleaning instructions.
m
onTHly
m
ainTenance
s
Pare
f
ilTers
Helps keep dirt and lint out of the air and off the coil,
thus increasing the unit's efficiency. Amana® brand
filters are easy to remove, wash and replace.
thus increasing the unit's efficiency. Amana® brand
filters are easy to remove, wash and replace.
FK10A
10-pack - A Series
FK10B
10-pack - B, C & D Series
FK10E
10-pack - E Series (This
model requires 2 filters
per change.)
model requires 2 filters
per change.)
r
ePlacemenT
c
Harcoal
f
ilTer
k
iT
Absorbs airborne odors caused by cigarette, pipe
or cigar smoke and odors caused by mold, mildew,
etc. Filters are made of polyester fibers coated with
activated charcoal and are individually wrapped. These
filters are permanent and can be washed or cleaned.
Call your Amana® brand PTAC sales person for details.
10 filters per pack.
or cigar smoke and odors caused by mold, mildew,
etc. Filters are made of polyester fibers coated with
activated charcoal and are individually wrapped. These
filters are permanent and can be washed or cleaned.
Call your Amana® brand PTAC sales person for details.
10 filters per pack.
CFK10A
10-pack - A Series (R-22)
CFK10B
10-pack - B, C & D Series (R-22)