Frigidaire FGEC3045KB 安装指导
7
ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS
4. Models: 30" and 36" (36" X 21½") Coil Elements
Cooktops
- These cooktops are designed to fit various cutout sizes.
The minimum and maximum cutout openings are
shown in figure 1.
shown in figure 1.
- If cooktop is to be used in new installation, use
minimum cutout dimensions in figure 1.
- Attach cooktop to cabinet using wood screws through
holes in vertical walls of burner box.
- If cooktop is to be installed as a replacement in
an existing countertop opening (not exceeding
maximum cutout dimensions as shown in figure
1), the following steps must be taken:
maximum cutout dimensions as shown in figure
1), the following steps must be taken:
1. Insert 4 screws and installation spacers through holes
in vertical walls of burner box (see figure 13).
2. Place cooktop into countertop opening and center
unit in cutout.
3. Tighten each screw finger tight or until spacers are
snug against burner box walls.
Figure 13
Burner box
Screw
Spacer
3. Models: 32" Coil Elements Cooktops
1. Place cooktop into countertop opening and center
1. Place cooktop into countertop opening and center
unit in cutout.
2. Remove all surface units and drip bowls.
3. Unit clamp down information. Once unit is installed in
3. Unit clamp down information. Once unit is installed in
counter opening, you must clamp unit down as shown
in figure 12.
in figure 12.
4. Put back all surface units and drip bowls.
5. Make electrical connections as outlined in "Electrical
5. Make electrical connections as outlined in "Electrical
Connection" section.
Figure 12
Reach down through surface unit openings and install
the four hold down retainers with screws as shown. Be
certain cooking top is firmly retained to counter top.
Cooktop
Burner box
Hold down retainer
Countertop
Nylon spacer
4. Prior to tightening installation screws, exert downward
pressure on burner box to assure flanges on burner
box rest firmly on counter. Tighten all screws evenly.
box rest firmly on counter. Tighten all screws evenly.
5. Unit clamp down information. Once unit is installed in
counter opening, you must clamp unit down as shown
in figure 14.
in figure 14.
6. Make electrical connections as outlined in "Electrical
Connection" Section.
Checking Operation
Refer to the Owner's Guide for operation.
CAUTION
Do not touch cooktop glass or elements.
They may be hot enough to burn.
Model and Serial Number Location
The serial plate is located under the cooktop or in the
burner box and can be seen by lifting up the main top of
unit.
burner box and can be seen by lifting up the main top of
unit.
When ordering parts for or making inquires about your
cooktop, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your cooktop.
cooktop, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your cooktop.
Before You Call for Service
Read the Avoid Service Checklist and operating
instructions in your Owner's Guide. It may save you time
and expense. The list includes common occurrences that
are not the result of defective workmanship or materials
in this appliance.
instructions in your Owner's Guide. It may save you time
and expense. The list includes common occurrences that
are not the result of defective workmanship or materials
in this appliance.
Refer to the warranty in your Owner's Guide for our
service phone number and address. Please call or write
if you have inquiries about your product and/or need to
order parts.
service phone number and address. Please call or write
if you have inquiries about your product and/or need to
order parts.
Figure 14
To clamp down, insert bracket with offset side of
angle into slot on each side of unit. The screw should
then be run through bracket and against bottom of
counter. Tighten until draws down.
Countertop
Cooktop
Screw
Hold down retainer
Burner box