Amana PTC093G25AXXX 规格说明表单
SS-DPTAC www.amana-ptac.com
5
4
www.amana-ptac.com SS-DPTAC
P
roduCT
s
PeCifiCATions
P
roduCT
s
PeCifiCATions
(Primary Heating for PTC Models; Auxiliary Heating for PTH Models; See below for Power Cord Configuration)
P
roduCT
s
PeCifiCATions
: PTC / PTH m
odels
— e
leCTriC
H
eAT
P
erformAnCe
Notes:
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
¹ All 265-volt models must use an Amana® brand sub-base (PTSB4**E) or an Amana® brand hard-wire kit (PTPWHWK4).
² Minimum Circuit Ampacity (MCA) ratings conform to the National Electric Code; however, local codes should apply.
³ Minimum voltage on 230/208-volt models is 197 volts; maximum is 253 volts.
Minimum voltage on 265-volt models is 238.5 volts; maximum is 291.5 volts.
⁴ Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265-volt models must be cartridge-style time-delay
fuses (included and factory-installed on all Amana® brand 265-volt chassis). See heater performance for total MCA.
⁵ Heating capacity and efficiency based on unit operation without condensate pump; unit automatically switches to electric heat
at approximately 24°F outdoor ambient.
⁶ Total watts for 12,000 and 15,000 BTU/h models; subtract 70 watts for PT07/09*E**A*
⁷ Specify two-digit heater kW size to complete model number.
⁸ Total amps for 12,000 and 15,000 BTU/h models; subtract 0.2 amps for PT07/09*E*A*.
⁹ R-410A refrigerant used in all systems.
¹⁰ All units meet or exceed ASHRAE 90.1 standards.
¹¹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹² Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
⁷ Specify two-digit heater kW size to complete model number.
⁸ Total amps for 12,000 and 15,000 BTU/h models; subtract 0.2 amps for PT07/09*E*A*.
⁹ R-410A refrigerant used in all systems.
¹⁰ All units meet or exceed ASHRAE 90.1 standards.
¹¹ All units less than 250 volts have a Leak Current Detector Interrupter (LCDI) power cord and meet UL 484 standards.
¹² Refer to electric heat performance data for total MCA and recommended overcurrent protection. Amps and Watts notation refers to compressor only.
Voltage
Electric
Heat (kW)
No. of
Stages
Stages
Nominal Heating (BTU/h)
Total
Watts
6
Total
Amps
Amps
Min. Circuit
Ampacity²
MOP
4
(amps)
Power
Cord
@ 230V
@ 208V
@ 265V
230/208V
2.5
1
8,500
6,800
- -
2,570 / 2,115
11.2 / 10.1
14.0
15
6-15 P
230/208V
3.5
1
12,000
9,900
- -
3,570 / 2,935
15.5 / 14.1
19.4
20
6-20 P
230/208V
5
1
17,100
14,000
- -
5,070 / 4,160
22.1 / 20.0
27.5
30
6-30 P
265V
2.5
1
- -
- -
8,500
2,570
9.7
12.1
15
7-20 P
265V
3.7
1
- -
- -
12,600
3,770
14.2
17.8
20
7-20 P
265V
5
1
- -
- -
17,100
5,070
19.2
23.9
25
7-30 P
* PTH/PTC09*E50*/* has the same airflow as a PTC/PTH12*E**** (not available on 7,000 BTU/h models).