Amana PTC093G25AXXX 目录
CT-DPTAC
www.amana-ptac.com
7
a
ccessories
(
conT
.)
Hard-wire Kits
Used to permanently wire to the chassis when a standard sub-base
and power cord are not utilized.
Used to permanently wire to the chassis when a standard sub-base
and power cord are not utilized.
PTPWHWK4
Armored Cable -
all voltages
all voltages
PTQCO3A
Quick Connect -
230/208V
230/208V
PTQC04A
Quick Connect -
265 & 115 V
265 & 115 V
Power Disconnect Switch
The PSHW**A power disconnect switch can be used for 265-volt or
230/208-volt physical disconnect, where required by local codes.
The switch is rated at 30-amp capacity. The switch is for use with and
Amana® brand standard sub-bases or PTPWHWK4 Hard Wire Kit.
The PSHW**A power disconnect switch can be used for 265-volt or
230/208-volt physical disconnect, where required by local codes.
The switch is rated at 30-amp capacity. The switch is for use with and
Amana® brand standard sub-bases or PTPWHWK4 Hard Wire Kit.
PSHW03A
230/208V
PSHW04A
265V
Fuse Holder Kit
Cartridge-style fuses can be installed in the fuse holder for use in the
sub-base or chassis. Available in 15, 20 and 30 amp (included on 265-
volt unit).
Cartridge-style fuses can be installed in the fuse holder for use in the
sub-base or chassis. Available in 15, 20 and 30 amp (included on 265-
volt unit).
FHK315C
230/208V 15A
FHK315E
230/208V 15A (R-410A)
FHK320C
230/208V 20A
FHK320E
230/208V 20A (R-410A)
FHK330C
230/208V 30A
FHK330E
230/208V 30A (R-410A)
Circuit Breaker Kit (230/208V only)
The circuit breaker kit, available in 15, 20 or 30 amp, can be used
with Amana brand sub-bases. It gives overcurrent protection, and its
location allows you to turn the unit on or off without tools.
The circuit breaker kit, available in 15, 20 or 30 amp, can be used
with Amana brand sub-bases. It gives overcurrent protection, and its
location allows you to turn the unit on or off without tools.
CBK3**C
Circuit Breaker Kit
Duct Extension Kit
Extends air distribution to an adjoining room. Consists of a main duct for
the room of origin and an extension duct to reach the adjoining room
and terminal duct. PTDK01A allows for the new “B” series unit to work
with the “A” series duct kits.
Extends air distribution to an adjoining room. Consists of a main duct for
the room of origin and an extension duct to reach the adjoining room
and terminal duct. PTDK01A allows for the new “B” series unit to work
with the “A” series duct kits.
MDK02B
Main Duct – R-22
MDK01E
Main Duct – R-410A
EDK02B
Extension Duct
TRANSITION
BAFFLES
Main Duct Kit
TDK02
Terminal Duct
PTDK01A
Transition Duct Only – R-22
PTDK01E
Transition Duct Only –
R-410A
R-410A
Extension Duct Kit
Terminal Duct Kit
Power Vent Kit
Installation of Power Vent increases CFM up to approximately 95. Vent
door will automatically close when unit fan is off.
Installation of Power Vent increases CFM up to approximately 95. Vent
door will automatically close when unit fan is off.
R-410A models must have these kits installed at the factory.
PVK3A
230/208V – R-22
PVK4A
265V – R-22
PVK3E
230/208V – R-410A
PVK4E
265V – R-410A
Condenser Baffle Kit
For use on non-baffled grilles. These deflectors direct the air in toward
the center and away from the inlet to prevent recirculation of the hot
condenser air.
For use on non-baffled grilles. These deflectors direct the air in toward
the center and away from the inlet to prevent recirculation of the hot
condenser air.
DGK1B
Condenser Baffle Kit
Basepan
Condenser
Condenser Baffles