GE GTD45GASJWS 规格指南
GTD45GASJ
GE
®
Series 7.2 cu. ft. capacity Aluminized alloy drum gas dryer with HE Sensor Dry
Specification Created 7/15
For answers to your Monogram,
®
GE Profile
™
or GE
®
appliance questions, visit our
website at geappliances.com or call GE Answer Center
®
service, 800.626.2000.
EXHAUST OPTION: When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
GAS: An individual, properly-grounded branch
GAS: An individual, properly-grounded branch
circuit, with a three-prong grounding-type receptacle,
protected by a 15 or 20 amp circuit breaker or a time-
delay fuse is required.
GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A
GAS (BTU/HR): 22,000. Factory-equipped for
protected by a 15 or 20 amp circuit breaker or a time-
delay fuse is required.
GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A
GAS (BTU/HR): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install
a conversion kit. See dryer ducting information for
a conversion kit. See dryer ducting information for
proper installation.
NOTE: Dryer wall outlet must be located within 36"
NOTE: Dryer wall outlet must be located within 36"
of service cord entry and accessible when dryer is
mounted in position.
INSTALLATION INFORMATION: For complete
INSTALLATION INFORMATION: For complete
information, see installation instructions packed with
your dryer.
your dryer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a label
on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 3" front and rear
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of
60 sq. in. of open area equally distributed. If this closet contains both a washer and a
dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes,
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes,
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
DRYER EXHAUSTING INFORMATION :
- Use metal duct only, vertical and horizontal ducting.
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear
DRYER EXHAUSTING INFORMATION :
- Use metal duct only, vertical and horizontal ducting.