GE PSB9120X 规格说明表单
240407
PSB9120DF
GE Profile
™
Series Advantium
®
120V - 30 in. Wall Oven
Specification Revised 7/13
Prepare the opening
The Advantium 120V series can be installed in combination with
other GE/Monogram appliances. Always follow each product's
Installation Instructions to compete the installation.
The Advantium 120V series can be installed in combination with
other GE/Monogram appliances. Always follow each product's
Installation Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall
to the dimensions shown.
* For existing cutouts, a maximum width
Order a 30" wide single oven cabinet or cut the opening in a wall
to the dimensions shown.
* For existing cutouts, a maximum width
of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip
on each side of the cutout for securing
the oven.
is slightly wider, secure a furring strip
on each side of the cutout for securing
the oven.
• Allow 3/4" to 2-1/8" case trim overlap
on the sides and 7/8" overlap on the
bottom of the opening for all models.
The amount of overlap on the sides
depends on the actual cutout width.
Allow 1-1/4" case trim overlap on the
top for models PSB9120 and for models
ZSC1201 and ZSC1202.
bottom of the opening for all models.
The amount of overlap on the sides
depends on the actual cutout width.
Allow 1-1/4" case trim overlap on the
top for models PSB9120 and for models
ZSC1201 and ZSC1202.
• Oven overlaps will conceal cut edges on all sides of the opening.
Note: PSB9120 series Advantium can be installed below GE/GE Profile
non-downdraft gas and electric cooktops. It CANNOT be installed below
induction or Monogram (2GU3841385) gas cooktops.
non-downdraft gas and electric cooktops. It CANNOT be installed below
induction or Monogram (2GU3841385) gas cooktops.
Note: PSB9120 series Advantium oven comes with two lower trim
pieces. One is for use above 36-inch height installations and one is
for use below 36-inch installations. Use of the accessory drawer will
replace the bottom trim piece for applicable installations. Please see
installation instructions for full details.
pieces. One is for use above 36-inch height installations and one is
for use below 36-inch installations. Use of the accessory drawer will
replace the bottom trim piece for applicable installations. Please see
installation instructions for full details.
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
the cutout.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAutION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30-
pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30-
pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Preparation WIth an Accessory Drawer
Installation over a GE/Monogram
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
2” Min.
(3” recommended)
(3” recommended)
Per warming
drawer
requirement
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” min.
from floor
1” min.
above
toekick
Warming Drawer:
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
30”
23-1/2”
21”
2” Min.
Per Oven
Requirement
Per warming drawer requirement
2” Min.
(3” recommended)
(3” recommended)
25-1/4”
Min.
5” min.
from floor
1” min.
above
toekick
30”
23-1/2”
25-1/4”
Min.
21”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” min.
from floor
1” min.
above
toekick