Amana ASD2575BRB 业主指南

1. Unplug refrigerator or disconnect power.
2. Open both doors (refrigerator and freezer) and the water filter 

cover door. It is not necessary to remove the water filter itself. 

3. Remove the base grille by pulling up on the bottom outside 

corners. See Graphic 1.

4. Disconnect the water dispenser tubing located behind the 

base grille on the freezer door side. The dispenser tubing runs 
through the door hinge, and must be disconnected in order to 
remove the door. See Graphic 2. 

■

Press blue outer ring against the face of fitting and pull the 
dispenser tubing free.

NOTE: Keep the water tubing connector attached to the 
tube that runs underneath the freezer. The door cannot be 
removed if the connector is still attached to the tube that 
runs through the door hinge.

5. Disconnect the wiring located behind the base grille on the 

freezer door side. See Graphic 3.

■

Remove the wiring clip using a 

¹⁄₄" hex-head socket 

wrench.

■

Disconnect wiring plugs.

6. Close both doors and keep them closed until you are ready to 

lift them free from the cabinet.

7. Use a 

⁵⁄₁₆" hex-head socket wrench to remove the top left 

hinge as shown. See Graphic 4.
IMPORTANT: Do not remove either screw A.

8. Lift freezer door straight up off bottom hinge. See Graphic 5. 

The water dispenser tubing and wiring remain attached to the 
freezer door and pull through the bottom left hinge. 
NOTE: This may require two people - one to lift the door and 
another to feed the water tubing and wiring through the hinge. 

IMPORTANT: Rest the door on its side on a soft, clean 
surface, such as a towel, blanket or piece of cardboard. This 
will help avoid damaging the door, water tubing and wiring.

9. Remove top right hinge as shown. See Graphic 6.

IMPORTANT: Do not remove either screw A.

10. Lift the refrigerator door straight up off bottom hinge.

IMPORTANT: Rest the door on its side on a soft, clean 
surface, such as a towel, blanket or piece of cardboard. This 
will help avoid damaging the door.

11. It may not be necessary to remove the bottom hinges to move 

the refrigerator through a doorway. Both bottom hinges have 
similar construction. 

■

If necessary, disassemble the hinges as shown. See 
Graphic 7.

IMPORTANT: To aid in door alignment and closing, there 
is a shim located between the hinge and the cabinet. 
When the hinge is removed, the shim may fall out of 
place. If this occurs, set the shim aside so it can be put 
back in place when the hinge is reconnected later.

1. Replace both bottom hinges, if removed. Make sure the shim 

is between the hinge and cabinet. Tighten screws.

2. Before replacing the freezer door on the bottom left hinge, 

feed the wiring with the yellow plug and the water dispenser 
tubing through the hinge. Assistance may be needed.

NOTE: Provide additional support for the doors while the top 
hinges are being replaced. Do not depend on the door magnets to 
hold the doors in place while you are working.
3. Align and replace the top left hinge as shown. See Graphic 4. 

Tighten screws.

4. Reconnect water dispenser tubing and wiring.

IMPORTANT: Do not intertwine the water tubing and wiring 
bundles when reconnecting them.

■

Push tubing into fitting until it stops and the black mark 
touches the face of fitting. See Graphic 2.

■

Reconnect wiring plugs. Reinstall the wiring clip over the 
grommets. Tighten screw. See Graphic 3.

5. Replace the refrigerator door by lifting the door onto the 

bottom right hinge.

6. Align and replace the top right hinge as shown. See Graphic 6. 

Tighten screws.

7. Replace the ice storage bin (on some models) and any 

adjustable door or utility bins.

8. Plug into a grounded 3 prong outlet.

Your refrigerator has two front adjustable rollers — one on the 
right and one on the left. If your refrigerator seems unsteady or if 
you want the doors to close more easily, adjust the refrigerator's 
tilt using the instructions below:
1. Move the refrigerator into its final location.
2. Remove the base grille to locate the two leveling screws, 

which are part of the front roller assemblies on each side. 
See Graphic 8.

NOTE: Having someone push against the top of the refrigerator 
takes some weight off the leveling screws and rollers. This makes 
it easier to adjust the screws. 
3. Use a 

¹⁄₂" hex-head socket wrench to adjust the leveling 

screws. Turn the leveling screw to the right to raise that side of 
the refrigerator or turn the leveling screw to the left to lower 
that side. It may take several turns of the leveling screws to 
adjust the tilt of the refrigerator. See Graphic 8.

4. Open both doors again and check that they close as easily as 

you like. If not, tilt the refrigerator slightly more to the rear by 
turning both leveling screws to the right. It may take several 
more turns, and you should turn both leveling screws the 
same amount.

5. Use a bubble level to check the leveling of the refrigerator.
NOTE: Whenever you need to move the refrigerator, turn the 
leveling feet to the right until they are no longer touching the 
ground. This will allow the refrigerator to roll more easily.