Raritan Computer P2-UMT242 用户手册
C
HAPTER
2: I
NSTALLATION
15
5. Connect a P2CIM-PS2 and its server CPU.
a. Connect the cable strands of an appropriate P2CIM-PS2 to the desired ports on a server CPU:
i.
P2CIM-PS2 (IBM PS/2 compatible CPUs): Plug the HD15 strand into the CPU’s HD15 VGA
video port. Plug the purple 6-pin mini-DIN keyboard strand into the CPU’s 6-pin mini-DIN
keyboard port. Plug the light green 6-pin mini-DIN strand into the CPU’s 6-pin mini-DIN
mouse port.
video port. Plug the purple 6-pin mini-DIN keyboard strand into the CPU’s 6-pin mini-DIN
keyboard port. Plug the light green 6-pin mini-DIN strand into the CPU’s 6-pin mini-DIN
mouse port.
ii.
P2CIM-SUN (Sun compatible CPUs): Plug the HD15 strand into the CPU’s HD15 VGA
video port. Plug the 8-pin mini-DIN strand into the CPU’s 8-pin mini-DIN keyboard/mouse
port.
video port. Plug the 8-pin mini-DIN strand into the CPU’s 8-pin mini-DIN keyboard/mouse
port.
iii.
P2CIM-USB (USB CPUs of any platform or P2 CIM-SUSB): Plug the HD15 strand into the
CPU’s HD15 VGA video port. Plug the USB Type A strand into one of the CPU’s USB Type
A ports.
CPU’s HD15 VGA video port. Plug the USB Type A strand into one of the CPU’s USB Type
A ports.
iv.
AUATC (serial CPUs, routers, etc.): Please see Appendix E: Using AUATC for RS-232
Access for installation instructions.
Access for installation instructions.
v.
Z-CIM (local [single-user] IBM PS/2 compatible CPUs): Please see Chapter 5: Paragon II
and Z-CIM for installation instructions.
and Z-CIM for installation instructions.
b. Plug in and power ON the CPU. If the P2CIM-PS2 is installed and operating properly, the
P2CIM-PS2’s green LED will start blinking: once per second while the P2CIM-PS2 is idle, more
quickly while data is passed in either direction.
quickly while data is passed in either direction.
c. Connect one end of a CAT5 UTP cable to RJ-45 port #1 on the back of the Base Unit. Connect the
other end of cable to the RJ-45 port on the P2CIM-PS2.
6. Configure the P2CIM-PS2 and the attached CPU.
a. The monitor attached to the User Station will display the Selection Menu; with the CPU you just
connected displayed in green. Use the up- and down-arrow keys to move the highlight to that entry
and press the [Enter] key. If you can access and operate the CPU normally, the P2CIM-PS2 is
connected successfully. Raritan recommends you give the server a meaningful system name at this
time, as described in the next steps.
and press the [Enter] key. If you can access and operate the CPU normally, the P2CIM-PS2 is
connected successfully. Raritan recommends you give the server a meaningful system name at this
time, as described in the next steps.
Note: If your video image is fuzzy (especially if you are using an LCD flat-panel monitor), you can adjust
the video gain to focus the video image. If the OSUI is not already displayed, activate it by pressing the
[Scroll Lock] key twice rapidly, then use the numeric keypad’s [+] and [–] (plus and minus) keys to adjust
the video image until it appears to be in focus.
the video gain to focus the video image. If the OSUI is not already displayed, activate it by pressing the
[Scroll Lock] key twice rapidly, then use the numeric keypad’s [+] and [–] (plus and minus) keys to adjust
the video image until it appears to be in focus.
b. Press
[F5] to activate the Administration Menu. Use the up- and down-arrow keys to move the
highlight to the Port Configuration entry and press the [Enter] key to select it.
Figure 21 Administration Menu