Haier HSU-12HKAG(R2DB) 用户手册

Operation

Emergency Operation:

temperature is below 16

o

C, do not use it in the 

Test operation:

Use this switch in the test operation when the room

normal operation.

 your finger from the switch: the cooling

Continue to press the test operation 

switch for more than 5 seconds. After

 you hear the "Pi" sound twice,release

Test operation switch is the same as emergency switch.

operation starts with the air flow speed "Hi".

 Use this operation only when the remote controller

 is defective or lost.

When the emergency operation switch is

pressed,the" Pi "sound is heard once, which means

the start of this operation.

In this operation, the system automatically selects

the operation modes,cooling or fan or heat,according

to the room temperature.

It is not possible to operate in dry mode.

    Room 

temperature

Operation

   mode

Designated

temperature

Timer

mode

Air flow

ABOVE 23

O

C

BELOW 23

O

C

COOLING

HEAT

23

O

C

26

O

C

NO

NO

AUTOMATIC

AUTOMATIC

Pi

(Cooling only uint）

Room  temperature

Operation

   mode

Designated

temperature

Timer

mode

Air flow

BELOW 23

O

C

FAN

26

O

C

NO

AUTOMATIC

Pi Pi

 After 30 minutes, test operation ends automatically(Only for 22K,24K unit).

3

Note ：

During TURBO operation, in rapid  COOL mode , the room

 will show inhomogeneous temperature distribution.

Long period QUIET operation will cause effect of not too 
cool or not too warm.

1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:

Remote controller:

Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). "      "or "      "will flash.

BLANK

TIMER ON TIMER OFF

TIMER ON-OFF

3.Press        /  

button to set time.

It can be adjusted within 24 hours.

Hints:
After replacing batteries or a power failure happens, time
setting should be reset.

According to the Time setting sequence of TIMER ON or

TIMER OFF, either Start-Stop or Stop-Start can be achieved. 

TIMER OFF-ON

0.5h

0.5h

0.5h

0.5h

Press the button for each time, setting time in the first 
12 hours increased by 0.5 hour every time, after 12 
hours,increased by 1 hour every time.

Press the button for each time, settiing time in the first 
12 hours decreased by 0.5 hour every time, after 12 
hours,decreased by 1 hour every time.

After adjust the time,press          button and confirm the

time ON or OFF button will not flash any more.

4.Confirm timer setting

5.Cancel timer setting
Press the timer button by times until the  time display 
eliminated.

(This function is unavailable on some models.) 

(1)

TURBO Operation

(2)

QUIET Operation

When you need rapid heating or cooling, you can use this function. 

Press           button to enter additional options, when cycle 
display to      ,       will flash，and then press         ,enter to 
quiet function. When cancel the function, please enter 
additional options again and to cancel quiet function.

Press TURBO  button, the remote controller will show         , 
and then achieve to the turbo function. Press again this 
TURBO  button , the turbo function will be cancelled.

Press           button to enter additional options, when cycle 
display to      ,       will flash，and then press         ,enter to 

health function. When cancel the function, please enter 

additional options again and to cancel health function.

(This function is unavailable on some models.) 

a lot of anion effectively balance the quantity of position

up the dust sediment in the room and finally clean the

and anion in the air and also to kill bacteria and speed

air in the room.

The anion generato

r 

in the airconditioner can generate