Grizzly G0568 用户手册
BdYZa<%*+-$<%*+.B[\#&%$%)
"(&"
Figure 36
#JeeZgWaVYZ\j^YZXdcigdahgZVg
k^Zl#
3.
;Vb^a^Vg^oZndjghZa[l^i]i]ZWaVYZ\j^YZXdc"
igdahh]dlc^cFigure 36 & 37#
<j^YZ7adX`
6hhnHXgZl
AViZgVa6Y_#
GdY7dai
7ZVg^c\
GdiVi^dc7dai
<j^YZ
7ZVg^c\h
4.
AddhZci]ZaViZgVaVY_jhibZcigdYWdai!addh"
Zci]ZhjeedgiWZVg^c\VY_jhibZcih]V[iWdai!
VcYVY_jhii]ZWaVYZ\j^YZhjci^ai]ZZY\Zhd[
i]ZWZVg^c\hVgZ
VcYVY_jhii]ZWaVYZ\j^YZhjci^ai]ZZY\Zhd[
i]ZWZVg^c\hVgZ
&
$
&+
WZ]^cYi]ZWaVYZ\jaaZih!
Vh^aajhigViZY^cFigure 38#
Note: The
1
/
16
" spacing is ideal, although with
larger blades it may not be possible. In such
cases, adjust the guide bearings as far for-
ward to the blade gullets as possible, and still
maintain the proper support bearing spacing
adjustment.
cases, adjust the guide bearings as far for-
ward to the blade gullets as possible, and still
maintain the proper support bearing spacing
adjustment.
Figure 37.
JeeZgWaVYZ\j^YZXdcigdah[gdci
k^Zl#
Hjeedgi7ZVg^c\
6Y_jhibZciH]V[i7dai
7ZVg^c\
GdiVi^dc
7dai
@cjgaZY
@cdW
Figure 38.
AViZgVaVY_jhibZcid[WaVYZ\j^YZh#
7aVYZ
<jaaZi
NOTICE
Make sure that the blade teeth will not con-
tact the guide bearings when the blade is
against the rear support bearing during the
cut or the blade teeth will be ruined.
tact the guide bearings when the blade is
against the rear support bearing during the
cut or the blade teeth will be ruined.
5.
I^\]iZci]ZaViZgVaVY_jhibZcigdYWdai#
6.
AddhZc i]Z WZVg^c\ gdiVi^dc Wdaih dc Wdi]
h^YZhd[i]ZWaVYZ#
7.
GdiViZi]Z`cjgaZY`cdWhidedh^i^dci]ZWZVg"
^c\h%#%%)VlVn[gdbi]ZWaVYZ#
Note: 0.004" is approximately the thickness
of a dollar bill.
of a dollar bill.
8.
I^\]iZc Wdi] d[ i]Z i]Z WZVg^c\ gdiVi^dc
VY_jhibZciWdaihidadX`i]ZWaVYZ\j^YZWZVg"
^c\h^cedh^i^dc#
^c\h^cedh^i^dc#
NOTICE
Whenever changing a blade or adjusting ten-
sion and tracking, the upper and lower blade
support bearings and guide bearings must
be properly adjusted and locked before cut-
ting operations.
sion and tracking, the upper and lower blade
support bearings and guide bearings must
be properly adjusted and locked before cut-
ting operations.