Frigidaire Side by Side Refrigerator With Electronic Controls 241695101 用户手册
25
BEFORE YOU CALL (CONTINUED)
PROBLEM CAUSE
CORRECTION
AUTOMATIC ICE MAKER (CONTINUED)
Ice maker is not making
enough ice.
enough ice.
•
Ice maker is producing less ice
than you expect.
than you expect.
•
Freezer is not cold enough.
•
Household water line valve is
not completely open.
not completely open.
•
Check to see if water
dispenser is dispensing slower
than normal.
dispenser is dispensing slower
than normal.
•
Ice maker should produce approximately 4 – 5 pounds
of ice every 24 hours.
of ice every 24 hours.
Extra Ice should produce up to 8
pounds of ice every 24 hours.
•
See PROBLEM section TEMPERATURES ARE TOO
WARM.
WARM.
•
Turn on household water line valve.
•
If it is, replace the ice & water filter cartridge.
Ice maker will not stop
making ice.
making ice.
•
Ice maker wire signal arm is
being held down by some item
in the freezer.
being held down by some item
in the freezer.
•
Move item and release wire signal arm. Remove any
ice cubes that are frozen together over the wire signal
arm.
ice cubes that are frozen together over the wire signal
arm.
Ice maker is not separating
the ice cubes.
the ice cubes.
•
Ice cubes are not being used
frequently enough.
frequently enough.
•
Ice cubes are hollow or smaller
than normal.
than normal.
•
Remove and shake ice container to separate cubes.
•
The ice & water filter cartridge may be clogged.
Replace filter cartridge.
Replace filter cartridge.
Ice has bad odor and taste.
•
Ice has picked up odor or
flavor from strong food stored
in refrigerator or freezer.
flavor from strong food stored
in refrigerator or freezer.
•
Water running to ice maker
has poor taste or odor.
has poor taste or odor.
•
Ice not used frequently enough.
•
Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.
produce fresh supply.
•
Add filter to water supply line. Consult a water
purifying company.
purifying company.
•
Discard stale ice.
ICE DISPENSER
Dispenser will not dispense
ice.
ice.
•
Ice storage container is empty.
•
Freezer temperature is set too
warm.
warm.
•
Household water line valve is
not open.
not open.
•
Freezer door is not closed.
•
Ice dispensing arm has been
held in for more than 4-5
minutes.
held in for more than 4-5
minutes.
•
When the first supply of ice is dropped into the
container, the dispenser should operate.
container, the dispenser should operate.
•
Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is made,
dispenser should operate.
cubes will be made. When first supply of ice is made,
dispenser should operate.
•
Open household water line valve. Allow sufficient time
for the ice to be made. When ice is made, the
dispenser should operate.
for the ice to be made. When ice is made, the
dispenser should operate.
•
Ensure freezer door is closed.
•
Motor is overloaded. Motor overload protector will
reset in approximately 3 minutes. Ice can then be
dispensed.
reset in approximately 3 minutes. Ice can then be
dispensed.
Ice dispenser is jammed.
•
Ice has melted and frozen
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.
•
Ice cubes are jammed
between ice maker and back
of ice container.
between ice maker and back
of ice container.
•
Ice cubes are frozen together.
•
Ice cubes are hollow or smaller
than normal.
than normal.
•
Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.
•
Remove ice cubes that are jamming the dispenser.
•
Use the dispenser often so that cubes do not freeze
together.
together.
•
The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 30 – 100 psi water pressure. Well
water pressures should fall within this range.
Replace the filter cartridge. Dispensing system
operates best at 30 – 100 psi water pressure. Well
water pressures should fall within this range.