Faber 630006370 产品宣传页

upper 

chimney 

cover

ductless 

lower 

chimney 

cover

canopy

(varies depending on installation)

min - 24”, suggested max - 30”

cabinet base

10" min

16 

1/8”

 max

21 

1/4"

2 

3/8"

36”

19 

9/32"

also consult cooktop

manufacturer's recommendation

8' 

3 5/8"

8' 

9 3/4"

8' 

1 5/8"

8' 

7 3/4"

7' 

11 5/8"

8' 

5 3/4"

7' 

9 5/8"

8' 

3 3/4"

upper 

chimney 

cover

lower 

chimney 

cover

canopy

(varies depending on installation)

min - 24”, suggested max - 30”

cabinet base

5 

1/8”

 min

16 

1/8”

 max

21 

1/4”

2 

3/8"

36”

19 

9/32"

also consult cooktop

manufacturer's recommendation

7' 

10 3/4"

8' 

9 3/4"

7' 

8 3/4"

8' 

7 3/4"

7' 

6 3/4"

8' 

5 3/4"

7' 

4 3/4"

8' 

3 3/4"

Note: If 24” or 30” High Backsplash is being installed, the distance between the bottom of the hood and the cooktop (distance x in diagram) is equal 

to the height of the Backsplash.

 

For ducted installations, the 

chimneys can be adjusted for 

ceilings between 7’ 4 3/4” and 

8’ 9 3/4” depending on the 

distance between the bottom 

of the hood and the cooktop 

diagram).
For ductless installations, the 

chimneys can be adjusted 

for  ceilings  between  7’  9 

5/8” and 8’ 9 3/4” depending 

on  the  distance  between 

the bottom of the hood and 

the cooktop (distance x in 

Ductless diagram).
For  shorter  ceilings,  have 

the chimney cover(s) cut at 

a sheet metal shop.    For 

higher ceiling installations, 

the High Ceiling Chimney 

Kit includes a new 40” upper 

chimney which would replace 

the 16 1/8” upper chimney 

that came with the hood.

Product specifications are subject to change without notification.  Consult the installation instructions before you begin installing this rangehood.

Important: Consult the installation 

instructions before you begin installing this rangehood.

For installations where ductwork is impos-
sible or highly impractical, a Ductless 
Conversion Kit is available.  A charcoal 
filter, which attaches under the blower 
assembly, absorbs smoke and odors.  A 
ductless diverter assembly directs the air 
out to a lower chimney with vent grates cut 
into the sides.

Make your ductrun as straight and short as possible.  The ductrun should not exceed 
35 equivalent feet if ducted with the required minimum of 6” round duct.  Count 45º 
angles as 3 feet, 90º elbows as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° elbows. Make sure that there is a 
minimum of 24” of straight duct between elbows if more than one is used. Do 
not install two elbows together. If you must elbow right away, do it as far away 
from the hood’s exhaust opening as possible.

Important: Consult the installation instructions before you begin installing this rangehood.