Manitowoc Ice K00042 产品宣传页

                                                   Installation Instructions 

The K00042 stacking kit is used for stacking a G-0600 ice 
machine on an E-1100 ice machine.  The bin must be leveled 
before proceeding. 
Installing the E-1100 Ice Machine 
1.  See service manual for uncrating and inspection of ice 

machine. 

2.  Remove top cover and side panels from ice machine. 
3.  Set ice machine carefully and squarely on bin. 
4.  Position top cover from kit on right-hand side of ice 

machine.  Position left-hand top cover.  Attach water 
shield to right-hand top cover on flange with one #8 x 
1/2” long sheet metal screw from kit (see Illustration 1). 

5.  Apply foam tape from the kit, as shown in Illustration 1. 
Installing the G-0600 Ice Machine 
1.  See service manual for uncrating and inspection of ice 

machine. 

2.  Remove top cover and side panels from ice machine. 
3.  Set G-0600 on top of E-1100 with backs of both 

machines being flush. 

4.  Remove screw from rear panel of G-0600 and screw from 

E-1100 in area of electrical hook-up (rear panel).  Apply 
rear-locking plate using existing screws that were 
removed.  With offset rear locking plate fastened, the left 
and right side of the G-0600 should be sitting on the E-
1100 top covers, as shown in Illustration 2. 

5.  Before applying RTV sealant in designated areas to insure 

against leaks or water hang-up, as shown (Illustration 2), 
remove the water pump, water curtain, and water trough.  
After sealing the seams with RTV, replace the water 
pump, etc. 

Installing the Ice Chute 
1.  Attach bottom mounting bracket from kit to the front base 

channel of the E-1100 using two #10-24 x 5/8” long sheet 
metal screws provided (see Illustration 2 and 3). 

2.  Remove angle “A” from upper G-0600 (see Illustration 

2). 

3. 

Attach top mounting bracket from kit to top rail of E-
1100 using existing screw.

 

4. 

Reattach angle “A” to G-0600.

 

5. 

From the upper ice machine, carefully bring the ice chute 
down in place until the weld studs located on the ice 
chute go through the slotted holes in the bottom mounting 
bracket.  Secure with four wing nuts provided in the kit.

 

6. 

Check for free movement of the water curtains on both 
the G-0600 and E-1100 ice machines (styrene covers over 
evaporators).

 

7.  Reattach all panels of both ice machines. 
8.  Proceed to ice machine service manuals for electrical and 

water hook-ups and start-up procedure. 

 
Parts List 
 
Qty. 

 Description 

 Part 

No. 

 
  1 

#8 x 1/2” lg. Sheet Metal Screw ...... 5121531 

  2 

#10 -24 x 5/8” lg. Sheet Metal 

 Screw 

............................................... 

5202053 

  4 

#8-32 Wing Nut .............................. 5489021 

  1 

Top Mounting Bracket .................... 6625414 

  1 

Bottom Mounting Bracket ............... 6606514 

  1 

Water Shield .................................... 6625114 

  1 

Top Cover ....................................... 6852514 

  1 

LH Top Cover ................................. 6625314 

  1 

Ice Chute ......................................... 6625214 

  1 

Rear Locking Plate .......................... 6242914 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

2110 South 26 Street, P.O. Box 1720, Manitowoc, WI  54221-1720 USA                                                                                                           8002033 
Telephone 920-682-0161, Fax - Sales:  920-683-7589, Service/Parts: 920-683-7585,  Other:  920-683-7879                                            Rev. 05/16/01