Sharp AX-1100M 用户手册

4

• When replacing the plug please ensure that you 

use a BSI or ASTA approved plug to BS1363, this 
should be fi tted with a brown coloured 13 amp fuse 
approved by BSI or ASTA to BS1362. If you have 
any doubt about electrical connection seek the help 
of a qualifi ed electrician.

TO REPLACE THE MAINS PLUG
The wires in the mains cable are colour coded as 
shown:
Green and yellow stripes   = EARTH
Blue 

 

   = 

Brown   

 

 

= LIVE

As the colours in the mains lead of your oven may not 
correspond with the coloured marking identifying the 
terminals in your plug, connect the wires as described:
• The green and yellow wire to the plug terminal 

marked E or 

 or coloured green or coloured 

green and yellow.

• The blue wire to the plug terminal marked N or 

coloured black or coloured blue.

• The brown wire to the plug terminal marked L or 

coloured red or coloured brown.

Make sure the terminal screws are tight and the cable 
is held securely by the cable grip where it enters the 
plug.
Like most appliances in your home, your oven must 
be connected to a single phase 230-240V, 50Hz 
alternating current supply.
If you do not make the proper electrical connections 
you might damage the oven or injure yourself. Neither 
SHARP nor the supplier will be liable if this happens. 

1.  Remove all packing materials from the inside of the 

oven cavity. Discard the loose polythene sheet from 
between the door and cavity. Remove the feature 
sticker, if attached, from the outside of the door.

2.  Check the oven carefully for any signs of damage.
3.  Place the oven on a flat, level surface strong enough 

to support the oven’s weight plus the heaviest item 
likely to be cooked.

   This oven is designed for countertop use only. Steam 

is ventilated from the bottom of the oven. Make sure 
the escaping steam does not wet electrical outlets/
other electrical appliances.

 4. Place or mount the oven so that the bottom of the 

oven is 85 cm or more above the floor.

5.  Do not allow the power supply cord to run 

6.  Ensure there is a minimum of free space above the 

oven of 12 cm. 

7.  Securely connect the plug of the oven to a standard 

earthed (grounded) household electrical outlet. 

ELECTRICAL CONNECTION.
• Do not allow water to come into contact with the 

power supply cord or plug.

• Insert the plug properly into the socket.
• Do not connect other appliances to the same socket 

using an adaptor plug.

• If the power supply cord is damaged, it must be 

replaced by a SHARP approved service facility or a 
similarly qualifi ed person to avoid a hazard.

• When removing the plug from the socket always grip 

the plug, never the cord as this may damage the 
power supply cord and the connections inside the 
plug.

• If the plug fitted to your oven is a rewireable type 

and in the event of the socket outlet in your home not 
being compatible with the plug supplied, remove the 
plug properly (do not cut off).

• If the plug fi tted to your oven is a non-rewirable type 

and in the event of the socket outlet in your home not 
being compatible with the plug supplied, cut-off the 
mains plug.

• Refi t with a suitable type, observing the wiring code 

given in ‘To replace the mains plug’.

IMPORTANT!
• The fuse from the cut-off plug should be removed and 

the plug disposed of in a safe manner.

• Under no circumstances should the cut-off plug be 

inserted into a socket outlet as a serious electric 
shock may occur.

• The plug must not be used without the fuse cover 

fi tted.

• If you have any doubt about your microwave oven 

obtain the help of a qualifi ed electrician.

SUK AX1100M_eng.indd   4

SUK AX1100M_eng.indd   4

10.9.8   4:57:49 PM

10.9.8   4:57:49 PM