Sony 8000SF 用户手册
280
Names and Functions of Parts of the Control Panel
Ch
apt
apt
to is a VTR/disk recorder, the start
point updated by the setting of the
[TIMELINE] button is as follows.
When the [TIMELINE] button is
point updated by the setting of the
[TIMELINE] button is as follows.
When the [TIMELINE] button is
On: start point of the timeline
When the [TIMELINE] button is
Off: start point of Cueup & Play
STOP TC: Press this button to set the
timecode of the stop point at that time.
The timecode of the stop point is
updated to the current time each time
this button is pressed.
When the device the operation applies
to is a VTR/disk recorder, the stop
point updated by the setting of the
[TIMELINE] button is as follows.
When the [TIMELINE] button is
The timecode of the stop point is
updated to the current time each time
this button is pressed.
When the device the operation applies
to is a VTR/disk recorder, the stop
point updated by the setting of the
[TIMELINE] button is as follows.
When the [TIMELINE] button is
On: stop point of the timeline
When the [TIMELINE] button is
Off: stop point of Cueup & Play
SET START TC, SET STOP TC, SET
DUR: When pressed, these buttons
light green, “START TC”, “STOP TC”
or “DUR” appears in the numeric
keypad control block display, and you
can enter a timecode from the numeric
keypad. If you enter a numeric value
and press the [ENTER] button, the
button goes off, whereas if you press
the [ENTER] button without entering a
numeric value the numeric keypad
control block display shows
“--:--:--:--”. To exit the numeric value
entry mode, either repeat pressing the
same button, or press a different
numeric keypad control block linked
button, or a mode selection button such
as the [EFF] and [SNAPSHOT]
buttons in the numeric keypad control
block. If the timecode has been set
correctly, the entered numeric value
appears in the timecode display.
light green, “START TC”, “STOP TC”
or “DUR” appears in the numeric
keypad control block display, and you
can enter a timecode from the numeric
keypad. If you enter a numeric value
and press the [ENTER] button, the
button goes off, whereas if you press
the [ENTER] button without entering a
numeric value the numeric keypad
control block display shows
“--:--:--:--”. To exit the numeric value
entry mode, either repeat pressing the
same button, or press a different
numeric keypad control block linked
button, or a mode selection button such
as the [EFF] and [SNAPSHOT]
buttons in the numeric keypad control
block. If the timecode has been set
correctly, the entered numeric value
appears in the timecode display.
STB (standby) OFF: When pressed, this
button flashes amber, and the device
selected with the device selection
selected with the device selection
buttons exits from the standby mode.
This button cannot be used for frame
memory clip operations.
This button cannot be used for frame
memory clip operations.
CUE: When pressed, this button flashes
amber together with the [ALL STOP]
button, and the device selected with the
device selection button is cued up to the
start point of the material. When more
than one device is selected, the amber
flashing continues until the reference
device is cued up, and when the cueing
up is finished, this button lights green.
button, and the device selected with the
device selection button is cued up to the
start point of the material. When more
than one device is selected, the amber
flashing continues until the reference
device is cued up, and when the cueing
up is finished, this button lights green.
REW: When pressed, this button lights
amber, and material of the device
selected with the device selection
buttons is rewound. To stop during the
rewind, press the [STOP] button or
[ALL STOP] button.
selected with the device selection
buttons is rewound. To stop during the
rewind, press the [STOP] button or
[ALL STOP] button.
PLAY: When pressed, this button lights
amber, and the device selected with the
device selection buttons plays. The
playback stops not only if the [STOP]
button is pressed, but also if any of the
[STB OFF], [SHTL], [JOG], [CUE],
[REW], [PLAY], [FF], and [ALL
STOP] buttons is pressed. When the
[VAR] button is pressed while the
device is playing back, the device plays
at one times normal speed in variable
mode.
device selection buttons plays. The
playback stops not only if the [STOP]
button is pressed, but also if any of the
[STB OFF], [SHTL], [JOG], [CUE],
[REW], [PLAY], [FF], and [ALL
STOP] buttons is pressed. When the
[VAR] button is pressed while the
device is playing back, the device plays
at one times normal speed in variable
mode.
FF: When pressed, this button lights amber,
and the material of the device selected
with the device selection buttons is fast
forwarded. To stop during the fast-
forward, press the [STOP] button or
[ALL STOP] button.
with the device selection buttons is fast
forwarded. To stop during the fast-
forward, press the [STOP] button or
[ALL STOP] button.
ALL STOP: When pressed, all device
material playback and other operations
stop. During cueing up of any of the
devices, this button flashes amber, and
when all cueing up operations are
completed, it lights green.
stop. During cueing up of any of the
devices, this button flashes amber, and
when all cueing up operations are
completed, it lights green.
REC: When pressed simultaneously with
the [PLAY] button, this button lights
red (the [PLAY] button lights amber),
red (the [PLAY] button lights amber),