Kingston Technology KVR1333D3D4R9SK3/24GI 数据表
Memory Module Specifications
KVR1333D3D4R9SK3/24GI
24GB (8GB 1024M x 72-Bit x 3 pcs.) PC3-10600
CL9 Registered w/Parity 240-Pin DIMM Kit
CL9 Registered w/Parity 240-Pin DIMM Kit
Kingston.com
Document No. VALUERAM0910-001.A00 05/10/10 Page 1
DESCRIPTION
ValueRAM’s KVR1333D3D4R9SK3/24GI is a kit of three 1024M
x 72-bit (8GB) DDR3-1333MHz CL9 SDRAM (Synchronous
DRAM) registered w/parity, Intel
x 72-bit (8GB) DDR3-1333MHz CL9 SDRAM (Synchronous
DRAM) registered w/parity, Intel
®
Compatibility Tested, dual-
rank memory modules, based on thirty-six 512M x 4-bit DDR3-
1333MHz SDRAMs. Total kit capacity 24GB. The SPDs are
programmed to JEDEC standard latency1333MHz timing of
9-9-9 at 1.5V. Each 240-pin DIMM uses gold contact fingers and
requires +1.5V. The electrical and mechanical specifications are
as follows:
1333MHz SDRAMs. Total kit capacity 24GB. The SPDs are
programmed to JEDEC standard latency1333MHz timing of
9-9-9 at 1.5V. Each 240-pin DIMM uses gold contact fingers and
requires +1.5V. The electrical and mechanical specifications are
as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8,9,10
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8,9,10
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does
not allow seamless read or write [either on the fly using A12
or MRS]
not allow seamless read or write [either on the fly using A12
or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), double sided component
• PCB : Height 1.180” (30.00mm), double sided component
SPECIFICATIONS
CL(IDD)
9 cycles
Row Cycle Time (tRCmin)
49.5ns (min.)
Refresh to Active/Refresh
160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin)
36ns (min.)
Power
4.365 W (operating per module)
UL Rating
94 V - 0
Operating Temperature
0° C to 85° C
Storage Temperature
-55° C to +100° C
Continued >>