Konica Minolta VI-9i 用户手册
263
Chapter
3
Error
Messages
Error Message (Alphabetically)
Cause
Action
The size of this image is different
from the size of selected image.
from the size of selected image.
The size of the selected image was dif-
ferent from that of the image you tried to
load, due to replacement of textures.
ferent from that of the image you tried to
load, due to replacement of textures.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
There are no points. The element
will be removed. (“File name”)
will be removed. (“File name”)
No data points were contained.
Click the [OK] button to close the mes-
sage dialog box. The element will be
selected.
sage dialog box. The element will be
selected.
This element does not have mul-
tiple images.
tiple images.
You attempted to execute the command
on an element that has only a single
image.
on an element that has only a single
image.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
This Shortcut key about [Com-
mand Name] is an invalid combi-
nation. It will be reset!
mand Name] is an invalid combi-
nation. It will be reset!
The shortcut key combination you at-
tempted to set is not supported by this
command.
tempted to set is not supported by this
command.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
This Shortcut key about [Com-
mand Name] is exist! Please set
another!
mand Name] is exist! Please set
another!
The same shortcut key had already been
assigned when you tried to assign it.
assigned when you tried to assign it.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
This version of scene file is not
supported.
supported.
The [Open] button was clicked even
though a scene file saved by the Utility
Software VI-S1 had been selected.
though a scene file saved by the Utility
Software VI-S1 had been selected.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
Too Small Mesh. We can’t get
enough information for registra-
tion.
enough information for registra-
tion.
Among selected elements, at least one
element that is composed of less than
a certain number of constituent points
exists.
element that is composed of less than
a certain number of constituent points
exists.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
Turntable not found.
The rotary stage is not connected to the
digitizer or it is not turned ON.
digitizer or it is not turned ON.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
Unknown PC Card
(VIVID 700, VI-700)
(VIVID 700, VI-700)
The type of memory card is incorrect.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
Value must be 0 < value < 10000.
A value outside the allowable range was
entered.
entered.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
Value must be –100000 < value <
100000.
100000.
A value outside the allowable range was
entered and the OK button was clicked.
entered and the OK button was clicked.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
VIVID busy.
The SCSI command did not complete.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
VIVID not found.
VIVID (VI) series digitizer is not turned
ON, cables are disconnected, or the
SCSI device driver setting is not correct.
ON, cables are disconnected, or the
SCSI device driver setting is not correct.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.
“Element name” Zero or few poly-
gons found. Skip making LOD.
gons found. Skip making LOD.
The selected element has an excessively
small number of polygons.
small number of polygons.
Click the [OK] button to close the mes-
sage dialog box.
sage dialog box.