Royal Sovereign RSS Series 用户手册

18

17

1. 

To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.

1. Remove the film from the laminator.

2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the

Teflon (metal) and silicone rollers.

NOTE: Rub firmly but do not scrub the rollers vigorously as this may scratch the

surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also

damage the rollers.

Machine will not turn
on:

a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.

a. Plug the power cord into appropriate

outlet.

b. Put the power switch to the “I” (On)

position.

c. Reset the circuit breaker.
d. Replace the fuse.

There is power, but the
rollers are not turning
after the “RUN” button
is pressed:

a. Emergency switch (es) is (are)

engaged.

b. Safety cover is not closed.
c. Paper guide is not installed correctly.
d. Blown motor fuse.

a. Disengage the emergency switch (es).
b. Close the safety cover to active the

safety switch.

c. Properly install the paper guide so that

the micro switch is activated.

d. Replace the motor fuse.

The unit is not heating
up:

a. The machine is in “COLD” mode.
b. Set temperature is lower than the room

temperature.

a. Switch to “HOT” mode.
b. Raise the temperature  according to the

recommended film temperature.

Curled lamination:

a. Upward curl.
b. Downward curl.

a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.

Unclear lamination:

a. The main roller temperatures are too

low and/or lamination speed is too fast.

a. Raise the roller temperatures and/or

lower the lamination speed.

AC 200, 220~240V

50/60Hz

2000W

3000W

685mm / 27"

1050mm / 41"

25 ~ 250mic / 1~10mil

6 m/min / 19.7 ft/min

10 min

Hot Shoe

DC geared

160°C / 320°F

9 settings

4 Roller

2.25", 3"

1 Blower

2 Blower

Yes

Yes

Yes

Yes

Yes

13mm / 0.5"

Motor

Yes

Yes

Yes

1070 x 650 x 1210 (mm)

1400 x 650 x 1210 (mm)

42" x 25.5" x 47.5"

55" x 25.5" x 47.5"

129kg / 285lbs

163kg / 360lbs

1260 x 900 x 1460 (mm)

1560 x 900 x 1460 (mm)

49.5" x 35.5" x 57.5"

61.5" x 35.5" x 57.5"

237kg / 523lbs

262kg / 578lbs

AC 200, 220~240V

50/60Hz

2000W

300W

685mm / 27"

1050mm /41"

25 ~ 250mic / 1~10mil

4 m/min / 13.1 ft/min

15 min

Rolling Shoe

DC geared

160°C / 320

°F

9 settings

4 Roller

2.25", 3"

1 Blower

2 Blower

Yes

Yes

Yes

Yes

Yes

13mm / 0.5"

Motor

Yes

Yes

Yes

1070 x 650 x 1210 (mm)

1400 x 650 x 1210 (mm)

42" x 25.5" x 47.5"

55" x 25.5" x 47.5"

123kg / 271lbs

157kg / 346lbs

1260 x 900 x 1460 (mm)

1560 x 900 x 1460 (mm)

49.5" x 35.5" x 57.5"

61.5" x 35.5" x 57.5"

231kg / 509lbs

256kg / 565lbs

Power supply

Power consumption

Max laminating width

Film thickness 

Max laminating speed

Ready time

Heating method

Driving motor

Max. temperature control

Speed control

Transport type

Film core size

Cooling system

Side cutter

Cross cutter

Film alignment

Hot lamination

Cold lamination

Mounting thickness 

Take up system

Paper counter

Length measurement

Reverse

Remote control

Foot pedal

Unit dimensions

(w x d x h)

Unit weight

Carton dimensions

(w x d x h)

Carton weight

AC 200,220~240V

50/60Hz

3000W

3300W

1050mm / 41"

1650mm / 65"

25 ~ 250mic / 1~10mil

Hot : 2 m/min / 6.6 ft/min

Cold : 1 m/min / 3.3 ft/min

25 min

40 min

Hot roller

DC geared

160°C / 320°F

9

settings

4 Roller

2.25", 3"

2 Blower

3 Blower

No

Yes

Yes

No

Yes

Yes

15(mm) / 0.6"

Motor

Yes

Yes

Yes

Yes

Yes

1400 x 650 x 1210 (mm)

1960 x 650 x 1210 (mm)

55" x 25.5" x 47.5"

77" x 25.5" x 47.5"

166kg / 366lbs

269kg / 593lbs

1560 x 900 x 1460 (mm)

2190 x 900 x 1460 (mm)

61.5" x 35.5" x 57.5"

86" x 35.5" x 57.5"

265kg / 584lbs

394kg / 869lbs