Diamondback 900Sr 用户手册
30
31
Workout Programs (Continued)
Workout Programs (Continued)
gram setup mode step by step as below:
Enter Age
The message window will fl ash a message of “ENTER AGE”, then “AGE = XX” with the number
1.
blinking.
You may press UP or
You may press UP or
2.
DOWN keys to adjust the age.
After age adjustment, the message display will switch to display “PRESS ENTER” to indicate
3.
next step. Press ENTER to accept and enter Weight adjustment.
Enter Weight
The message window will fl ash a message of “ENTER WEIGHT”, then “WEIGHT = XXX LB”
1.
with the number blinking. (WEIGHT = XXX KG” for metric system)
You may press
You may press
2.
UP or DOWN keys to adjust the weight
After weight adjustment, the message display will switch to display “PRESS ENTER” to indi-
3.
cate next step. Press ENTER to accept and enter Time adjustment.
Enter your workout time:
The message window will fl ash a message of “ENTER TIME”, then “TIME = 30 MIN” and the 30
1.
will be blinking.
You may press
You may press
2.
UP or DOWN keys to adjust the time. When the time setting reaches 60 min-
utes, the display will show “TIME = 1HR 00MIN” instead.
After time adjustment, the message display will switch to display “SET UP COMPLETED”, then
After time adjustment, the message display will switch to display “SET UP COMPLETED”, then
3.
“PESS START” to indicate next step. You may press, the ENTER or START/STOP key to
begin this program.
begin this program.
Or press the START/STOP key to accept current default values and begin the workout
Default time = 30 minutes
•
Default Intensity level = preset level as shown in dot matrix profi le
•
Age and weight will be what was enter and saved in a previous workout
•
During the Program
Once the Enter or Start key is pressed, the Warm Up will be active. See Warm Up mode section for de-
tails.
tails.
Main Display
As soon as the program will begins, the Dot Matrix will activate and the 1st segment of the program’s
•
profi le will start blinking
If there is a valid Heart rate signal being detected a heart shape will start blinking and the Heart rate
If there is a valid Heart rate signal being detected a heart shape will start blinking and the Heart rate
•
graph will light up with the percentage of maximum heart rate.
The message “Time” will light up in the date display and the Time will start counting down. To switch
The message “Time” will light up in the date display and the Time will start counting down. To switch
•
the data being displayed press the DISPLAY key to select from Time, Calories, Pulse and Distance
and to turn on and off the scan function.
and to turn on and off the scan function.
Message/Data Display
As soon as the program begins. The message display will turn into workout data display and display
•
four default data: Time, Level, Pulse & Calories and the LED on top of the Data Display key will be lit.
Press the “DATA DISPLAY” buttons to switch the display to “RPM, Speed, Distance & Watts”. The
Press the “DATA DISPLAY” buttons to switch the display to “RPM, Speed, Distance & Watts”. The
•
LED on the bottom of the key will light up.
Adjustment
Press
•
UP or DOWN key to adjust the intensity level from L1 to L16. The dot matrix window will up-
date the intensity profi le accordingly.
Ending the Program
When program time is up or
•
START/STOP key is pressed, this program will end and Cool Down will
be active.
The message display will fl ash a message “PROGRAM ENDED”&”COOL DOWN”. See Cool Down for
The message display will fl ash a message “PROGRAM ENDED”&”COOL DOWN”. See Cool Down for
•
details.
START/STOP
START/STOP
•
key could be pressed to re-start the Intervals program again.
START/STOP
•
key could be pressed and held for 2 seconds to skip the Cool Down and activate the
Workout Summary immediately.
Pause, Reset, Switch or Save a program
See Console Operating Tips section for details, page 16
Hill Climb
Getting Started
The Hill program simulates a hill climbing exercise with a preset hill profi le. The exercise
profi le will guide you up over a hill and down the other side.
Beginning the Program
During idle mode, the message window displays a message “SELECT A PROGRAM”. To
begin this program, press the HILL CLIMB program key, the LED indicator above it will
begin this program, press the HILL CLIMB program key, the LED indicator above it will
light up.
Entering the program
When the message display fl ashes, “HILL CLIMB” and “PRESS ENTER”, it indicates you are about to
select the Hill Climb program. Press ENTER Key to enter program setup mode or press the START/
STOP key to skip the set up mode and use default values.
select the Hill Climb program. Press ENTER Key to enter program setup mode or press the START/
STOP key to skip the set up mode and use default values.
Press ENTER key to enter program set up mode. The message display will take you through the pro-
gram setup mode step by step as below:
gram setup mode step by step as below:
Enter Age
The message window will fl ash a message of “ENTER AGE”, then “AGE = XX” with the number
1.
blinking.
You may press
You may press
2.
UP or DOWN keys to adjust the age.
After age adjustment, the message display will switch to display “PRESS ENTER” to indicate
3.
next step. Press ENTER to accept and enter Weight adjustment.
Enter Weight
The message window will fl ash a message of “ENTER WEIGHT”, then “WEIGHT = XXX LB”
1.
with the number blinking. (WEIGHT = XXX KG” for metric system)
900Ub.Sr OM.R1.indd 30-31
900Ub.Sr OM.R1.indd 30-31
6/11/2008 9:56:25 AM
6/11/2008 9:56:25 AM