Toshiba 30HFX84 用户手册
19
Appendix
Using the TV’
s
Features
Setting up
your TV
Using the
Remote Control
Connecting
your TV
W
elcome to
elcome to
T
oshiba
Important
Safeguards
Notes:
• Every time you replace the batteries, you
• Every time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes.These VCRs
have a switch labeled “VCR1/VCR2.”
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and
does not respond to any of the codes for
your VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
does not respond to any of the codes for
your VCR brand, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
Programming the remote control for use with
your audio/video devices
your audio/video devices
Device code setup
Searching and sampling the code of a device (8500)
Note: When a search cycle is completed, the mode indicator will blink
three times. The remote control will begin to cycle through the
available codes again. If no key is pressed within 10 seconds while
programming, the remote control will exit the program mode and
return to the previous code.
available codes again. If no key is pressed within 10 seconds while
programming, the remote control will exit the program mode and
return to the previous code.
1. Refer to the Device code table on pages 21–22 to find
the code for your device.
If more than one number is listed, try each one separately
until you find one that works.
until you find one that works.
2. Press MODE until the Mode indicator for the device
(CABLE/SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.
3. While holding down the RECALL button, press the
Channel Number buttons to enter the four-digit code of
your blank of device.
your blank of device.
If a valid code is entered, the mode indicator will blink
twice.
twice.
If an invalid code is entered, the mode indicator will blink
one long blink.
one long blink.
4. Point the remote control at the device and press POWER
to test the code.
If the device turns on, you have entered the correct code.
If the device does not respond to the remote control, you
may have entered the wrong code. Repeat steps 3 and 4
using another code.
may have entered the wrong code. Repeat steps 3 and 4
using another code.
5. Press MODE to select the TV mode to control the TV.
If you do not know the device code for a particular target unit, you can
cycle the remote control through the available codes for that device
mode and sample the functions to find the code that properly operates
the target device. The keys available to be sampled, provided they are
applicable to that mode, are 0, 1, 2, 3, POWER, VOL
cycle the remote control through the available codes for that device
mode and sample the functions to find the code that properly operates
the target device. The keys available to be sampled, provided they are
applicable to that mode, are 0, 1, 2, 3, POWER, VOL
C
, CH
C
, PLAY
and STOP. Invalid keys will be ignored while in program mode.
To cycle through each available device code and sample its functions:
1. Press MODE to select the mode you want to set up.
2. While holding down the RECALL button, press 8 –5 –0 –0.The
To cycle through each available device code and sample its functions:
1. Press MODE to select the mode you want to set up.
2. While holding down the RECALL button, press 8 –5 –0 –0.The
remote control will enter program mode.
3. Point the remote control at the target device and press POWER
(or other function buttons that are available to be sampled).
4. If the device responds to the remote control:
Press RECALL to store the device code.
The mode indicator will blink twice and the remote control will exit
The mode indicator will blink twice and the remote control will exit
the program mode.
If the device does not respond to the remote control:
Press
Press
C
, and then press POWER.
Repeat this step until the device responds to the remote control,
and then press RECALL.
POWER
Numbers
RECALL
MODE
C
Using the
Remote Control
3R40321A/E P16-23
9/7/04, 15:07
19