Vidikron VP-6000 用户指南
Vidikron PlasmaView Owner’s Operating Manual
39
PRE
L
IMINAR
Y
V-Size (Installer Adjust mode): Use the up- or down-arrow buttons (
,
) to highlight
V-Size. Then, press SET and use the right-arrow button (
) to increase the height; use the
left-arrow button (
) to decrease it.
Image Reset: To reset all screen settings for the current input to the default, Installer Adjust
mode values, select Image Reset from the Screen menu. Then, press
mode values, select Image Reset from the Screen menu. Then, press
to highlight YES and
press SET.
Set-Up
Color Temperature: To adjust the color temperature, select Color Temperature from the
Set-Up menu. (Color temperature defines the “color of gray.”) Use the left- and/or right-arrow
buttons to select LOW, MID-LOW, MIDDLE, MID-HIGH or HIGH. The default setting, MIDDLE, is
appropriate for most situations. Higher settings produce a “bluer” picture; lower ones cause
the image to appear more red.
Set-Up menu. (Color temperature defines the “color of gray.”) Use the left- and/or right-arrow
buttons to select LOW, MID-LOW, MIDDLE, MID-HIGH or HIGH. The default setting, MIDDLE, is
appropriate for most situations. Higher settings produce a “bluer” picture; lower ones cause
the image to appear more red.
Auto Off: When using the PlasmaView with a computer, set Auto Off to ON to have the
PlasmaView go into standby mode when no source signal is present on the current input. (A
warning message appears on-screen for approximately eight seconds before this occurs.) To
return to normal operating mode from the Auto Off standby mode, select the input with the
remote control or operate your computer.
PlasmaView go into standby mode when no source signal is present on the current input. (A
warning message appears on-screen for approximately eight seconds before this occurs.) To
return to normal operating mode from the Auto Off standby mode, select the input with the
remote control or operate your computer.
When Auto Off is disabled (OFF), the PlasmaView remains in normal operating mode,
regardless of the presence or absence of an input sync signal.
regardless of the presence or absence of an input sync signal.
The STANDBY/ON indicator at the front of the PlasmaView indicates the status of the power
management function, as described in Table 4-2.
management function, as described in Table 4-2.
Video NR: To apply Digital Noise Reduction (DNR) to the input signal, select Video NR from
the Set-Up menu. Noise reduction is useful for improving the signal-to-noise ratio of video
signals.
the Set-Up menu. Noise reduction is useful for improving the signal-to-noise ratio of video
signals.
Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping
in mind that higher settings (which reduce high frequencies) may also “soften” the image.
in mind that higher settings (which reduce high frequencies) may also “soften” the image.
INPUT 2
PLASMAVIEW
SCREEN
SET-UP
OPTION
PICTURE
SET
SET
EXIT
MENU
: MIDDLE
: OFF
: VID NR1
: LOW
: ON
: OFF
: RGB
: VID NR1
: LOW
: ON
: OFF
: RGB
: 720p
COLOR TEMP.
AUTO OFF
VID NR
MPEG FILTER
CHROMA EE
CINEMA MODE
COLOR SPACE
DVI SET UP
SIGNAL INFO
VID NR
MPEG FILTER
CHROMA EE
CINEMA MODE
COLOR SPACE
DVI SET UP
SIGNAL INFO
1. If the computer is turned off or not properly connected to the
PlasmaView, the system is set to the off state.
2. For instructions on using the computer's power management features,
refer to the instructions for your computer.
Table 4-2. Power Management Indications
Power
management
mode
STANDBY/
ON
Indicator
Power
management
operating status
Description
Turning the picture
back on
ON
Solid
green
green
Not activated.
Horizontal and
vertical
synchronizing
signals are present
from the computer.
vertical
synchronizing
signals are present
from the computer.
Picture already on.
OFF
Flashing
green
green
Activated.
Horizontal and/or
vertical
synchronizing
signals are not
present from the
computer.
vertical
synchronizing
signals are not
present from the
computer.
Press a key on the
keyboard or move
the mouse. The
picture reappears.
keyboard or move
the mouse. The
picture reappears.
Note