Samsung ITP-5121D 用户手册
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes
(see Answering Intercom Calls
under Intercom Calls
for descriptions).
•
While on-hook, press TRANSFER and then dial 103.
•
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
•
Press TRANSFER to store your selection.
From the LCD:
•
Press MENU button.
•
Scroll to SETUP option and press ENTER.
•
Scroll to ANSWERING MODE and press ENTER—OR—you may dial 1 and
immediately enter the option.
immediately enter the option.
•
Select desired station ring type setting. (Ring, Auto Answer, or Voice
Announce).
Announce).
•
Press ENTER to select and SAVE.
•
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
to idle screen.
NOTE: When your keyset is programmed for Auto Answer and you have Forward
No Answer (FNA) turned on, you must answer screened transfers by pressing the
SEND button before your FNA timer expires or the call will forward.
No Answer (FNA) turned on, you must answer screened transfers by pressing the
SEND button before your FNA timer expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
While on-hook, press TRANSFER and then dial 110.
•
Dial 15 to access AUTO ANS CO.
•
Press the VOLUME UP or DOWN key to change status.
•
Press TRANSFER to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line button, route button or a flashing CALL
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
•
With the handset on-hook, press TRANSFER and then dial 110.
•
Dial 001 to turn Automatic Hold on or 000 to turn it off.
•
Press TRANSFER to store your selection.
51
50
SELECT RING TONE
Each ITP-5112L user can select from a variety of ring tones.
From the LCD:
•
Press MENU button.
•
Scroll to SOUND/SCREEN option and press ENTER.
•
Scroll to RING TONE SELECT and press ENTER—OR—you may dial 1 and
immediately enter the option.
immediately enter the option.
•
Select from one of the three categories:
1.
1.
Standard Ring Tones
2.
Melody or
3.
My Ring Tones
•
Press ENTER to select. Use LEFT/RIGHT arrow buttons to scroll through the
available ring tones and press ENTER to SAVE.
available ring tones and press ENTER to SAVE.
•
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
to idle screen.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234. You can change your station pass-
code whenever you desire.
code whenever you desire.
•
While on-hook, press TRANSFER and then dial 101.
•
Dial your old passcode.
•
Dial a new passcode (must be four characters). You can use 0–9.
•
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
beeps indicate an incorrect code. Reenter the code again.
•
Press TRANSFER to store the new passcode.
From the LCD:
•
Press MENU button.
•
Scroll to MY PHONE option and press ENTER.
•
Scroll to CHANGE PASSWORD and press ENTER—OR—you may dial 3 and
immediately enter the option.
immediately enter the option.
•
Enter CURRENT PASSWORD, press ENTER.
•
Enter NEW PASSWORD and press ENTER.
•
Enter NEW PASSWORD again, for confirmation and press ENTER.
•
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
to idle screen.
Home Page
Table of Contents
ITP-5112L