Clarity WN=5230-S 用户手册
WN-5230-S VideoWall User’s Guide
23
To setup the WN-5230-S display in a video wall configuration, follow these
steps:
steps:
1. Grasp the screen on each side
at the bottom
The “screen” you are removing is 5 inches thick. Pull
out at the bottom first, to separate the latch-hooks
from the latches. It comes out with a “pop.” The
screen should now be loose at the bottom, but still
attached at the top.
out at the bottom first, to separate the latch-hooks
from the latches. It comes out with a “pop.” The
screen should now be loose at the bottom, but still
attached at the top.
2. Slip fingers between the screen
frame
Slip fingers between the screen frame and the
display chassis, as close to the top latches as
possible and pull the top of the screen from the
latches.
display chassis, as close to the top latches as
possible and pull the top of the screen from the
latches.
3. Using both hands…
Carefully remove the screen and set it aside.
4. Assemble the lower row first.
Line up the legs for the bottom row as straight as
possible.
possible.
Insert a ¼” X 2 ½” bolt through the holes as shown
at the bottom of Figure 1. Tighten a nut securely on
this bolt, but take care not to bend the legs.
at the bottom of Figure 1. Tighten a nut securely on
this bolt, but take care not to bend the legs.
Secure the legs to the floor. Use the tapped 5/16-18
holes in the front and rear of the legs. You can put an
eye-bolt in this hole and secure it to the floor with a
lag screw. Or use angle bracket, screwed to the floor
and bolted to this hole in front and rear. Or use the
optional BAS-520 base, securing it to the floor and
putting the lower row of displays on it.
holes in the front and rear of the legs. You can put an
eye-bolt in this hole and secure it to the floor with a
lag screw. Or use angle bracket, screwed to the floor
and bolted to this hole in front and rear. Or use the
optional BAS-520 base, securing it to the floor and
putting the lower row of displays on it.
Before going to the next higher rows, see that the
bottom row is straight. From one end of the line, look
along the front of the displays. The line should be
straight and flat. Level is not as important as straight
and flat.
bottom row is straight. From one end of the line, look
along the front of the displays. The line should be
straight and flat. Level is not as important as straight
and flat.
5. Stack the next higher row.
Slide the legs of each display into the mating sockets
of the display in the first (lower) row. Check it for
“straight and flat.”
of the display in the first (lower) row. Check it for
“straight and flat.”
6. Insert a bolt (supplied).
Insert a bolt through the hole in side wall of the lower
unit into each leg of the unit above.
unit into each leg of the unit above.
Tighten a nut on this bolt to lock the units together.
See Figure 1, above.
See Figure 1, above.
7. Continue with subsequent rows
of displays
Lock each display to the adjacent displays after the
row above it (if any) has been installed. Bolt the top
row together, even though there are no legs from a
higher row.
row above it (if any) has been installed. Bolt the top
row together, even though there are no legs from a
higher row.
8. For added stability…
Use the rear-tapped holes in the legs of the upper
units to fasten to a solid support, such as a structural
wall.
units to fasten to a solid support, such as a structural
wall.
The threaded inserts in each leg are female 5/16-18
UNC.
UNC.
9. Check
Check that all displays in the video wall are locked
together. Look again down the line from one end to
see that each row is straight and flat.
together. Look again down the line from one end to
see that each row is straight and flat.