Sony HES-V1000 用户手册
130
d At close range (2–4 inches, about 5–10 cm)
and facing the sensors on the server’s remote
and the AV amplifier’s remote, send the
remote code from the AV amplifier’s remote.
The device's button light pressed in step 2 (AMP)
turns off. Keep sending for more than one second
until the button flashes again.
and the AV amplifier’s remote, send the
remote code from the AV amplifier’s remote.
The device's button light pressed in step 2 (AMP)
turns off. Keep sending for more than one second
until the button flashes again.
e Check that AMP flashes again.
Learning has failed if AMP flashes five times. If it
flashes 10 times, the remote’s memory is full. Clear
the remote’s memory (page 130) and repeat from
step 1.
flashes 10 times, the remote’s memory is full. Clear
the remote’s memory (page 130) and repeat from
step 1.
f Press RM SET UP again to exit the Learning
mode.
To exit the Learning mode
Press RM SET UP. Or, leave the remote for more than 60
seconds without operating.
seconds without operating.
To erase a learned function
Example: Erasing the function assigned to “1” above.
1
While holding down RM SET UP, press CLEAR.
RM SET UP flashes twice.
RM SET UP flashes twice.
2
Press the device function button (AMP) to select
the function to erase.
AMP lights up and RM SET UP keeps flashing.
the function to erase.
AMP lights up and RM SET UP keeps flashing.
3
Press the device selection button you want to clear
(“1”).
AMP flashes twice and the device selection function
of “1” is cleared.
If it fails, RM SET UP flashes five times.
(“1”).
AMP flashes twice and the device selection function
of “1” is cleared.
If it fails, RM SET UP flashes five times.
z
Hint
See below when you want to clear the remote’s memory entirely.
To erase all learned functions
1
While holding down VOL –, press \/1 and AV
\/1 at the same time.
RM SET UP flashes three times.
\/1 at the same time.
RM SET UP flashes three times.
2
Release VOL –.
Saving Frequent
Procedures
Procedures
The MACRO function lets you register a sequential procedure
that consists of up to 30 presses of the remote’s buttons.
that consists of up to 30 presses of the remote’s buttons.
This function is convenient, for example, when you have many
devices in your home theater and need to press many buttons for
many devices before you start viewing.
devices in your home theater and need to press many buttons for
many devices before you start viewing.
Registering a MACRO
Note that the other devices need to be registered to the device
selection buttons (TV, VCR, etc.,) beforehand (page 129).
selection buttons (TV, VCR, etc.,) beforehand (page 129).
a While pressing down RM SET UP, press
MACRO 1/2/3 for more than one second.
The RM SET UP flashes twice, and the pressed
MACRO button lights up.
The RM SET UP flashes twice, and the pressed
MACRO button lights up.
b Press the device selection button to switch the
remote’s mode for the device (i.e., press TV to
operate a TV).
The device selection button flashes.
operate a TV).
The device selection button flashes.
c Set the button operations by pressing the
following function buttons.
d Repeat steps 2 to 3 to set the entire sequence.
RM SET UP flashes twice and lights up again each
time you press other buttons.
time you press other buttons.
e Press RM SET UP to finish.
Buttons
Functions
TV, VCR, AMP,
SAT/CABLE,
CUSTOM,
SERVER
SAT/CABLE,
CUSTOM,
SERVER
Switches the remote’s mode for the
device.
device.
MACRO1–3
Sets intervals before sending a signal
when pressed for more than one second.
(MACRO 1: 1 sec., MACRO 2: 5 sec.,
MACRO 3: 10 sec.)
when pressed for more than one second.
(MACRO 1: 1 sec., MACRO 2: 5 sec.,
MACRO 3: 10 sec.)
Other buttons
Sets the functions to perform.
SET
AV
HOME
RM SET UP
TV
AMP
VCR
CUSTOM
MACRO 1/2/3
SAT/CABLE
SERVER