Runco Q-1500D 用户手册
Q-1500d Series Installation/Operation Manual
65
PRE
L
IMINAR
Y
4.1
Using the On-Screen
Menus
Using the On-Screen
Menus
To display the Main Menu, press the MENU button on the remote control or Primary DHD
Controller front panel.
Controller front panel.
To select a menu item, use the
and
buttons on the remote control or Primary DHD
Controller front panel to highlight it. Then, to confirm your selection, press ENTER on the
remote control or DHD Controller front panel.
remote control or DHD Controller front panel.
The Q-1500d OSD menus are arranged hierarchically, as shown in Figure 4-1. Some
menu options apply only to certain input signal types. For example, Phase and Tracking
can only be adjusted for RGB, Component video or SCART signals.
menu options apply only to certain input signal types. For example, Phase and Tracking
can only be adjusted for RGB, Component video or SCART signals.
Figure 4-1. Q-1500d OSD Menu Structure
4. Operation
Input Source
Composite 1
Composite 2
Composite 3
Component
HD 1
HD 2
SCART
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Aspect Ratio
16:9
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Screen
Screen 1 / Screen 2
Picture
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
Input Position
Left/Right
Up/Down
Width
Height
Overscan
Overscan Mode
(Zoom/Crop)
(Zoom/Crop)
Phase
(RGB/Component/SCART signals only)
(RGB/Component/SCART signals only)
Tracking
(RGB/Component/SCART signals only)
(RGB/Component/SCART signals only)
Memory
Presets
Presets
Recall ISF Night or ISF Day
Recall/Save Custom 1 or Custom 2
Reset Custom 1 and Custom 2 to
Factory Default
Factory Default
Sleep Timer
Off, 30 Minutes, 60 Minutes, 90
Minutes, 2 Hours or 4 Hours
Minutes, 2 Hours or 4 Hours
Information
Signal
System
Network
Field Service
Manufacturing
Calibration
Display Color -
Common Settings
Common Settings
Gain
-100, -99... 0 ... 99, 100 (Red, Green, Blue)
Offset
Gamma
Mode
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35 or 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
(Simple / Advanced)
Simple
(1.8, 2.0, 2.2, 2.35 or 2.5)
Advanced
(0 (2.2 gamma curve),
1, 2, 3 ... 20 (custom gamma tables))
Color Temp
Simple (5500K, 6500K, 7500K or 9300K)
Color Gamut
Auto, REC709, SMPTE-C, EBU, Native or PCE
PCE
Hue (Red / Yellow / Green / Cyan / Blue / Magenta)
Saturation (Red / Yellow / Green / Cyan / Blue /
Magenta)
Level (Red / Yellow / Green / Cyan / Blue / Magenta)
Runco Smart Color (RSC) (On or Off)
White Balance (Red / Green / Blue Gain)
Saturation (Red / Yellow / Green / Cyan / Blue /
Magenta)
Level (Red / Yellow / Green / Cyan / Blue / Magenta)
Runco Smart Color (RSC) (On or Off)
White Balance (Red / Green / Blue Gain)
Display Color -
Projector Settings
Projector Settings
SatCo
On or Off
ConstantContrast
Low, Medium, High or Off
Engine Configuration
Dual / Single
Input Image
Brightness
-50, -49 ... 0 ... 49, 50
Contrast
Color
Tint
Sharpness
Color
Tint
Sharpness
Input Color
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and Component inputs only)
(HD 1, HD 2 and Component inputs only)
Offset
Chroma Delay
0, 1, 2 ... 7
(Composite inputs only)
(Composite inputs only)
Noise Filter
0, 1, 2 ... 63
Save ISF Night
Back / Confirm
Save ISF Day
Copy/Paste
Memory Preset
Copy Settings
Paste Settings
Paste Settings
Aspect Ratio
Copy Settings
Paste Settings
Paste Settings
Output Shift
Left/Right
-50, -49 ... 0 ... 49, 50
Up/Down
Width
Width
-50, -49, 48 ... 0
Height
Screen Masking
0, 1, 2 ... 100
(Top / Bottom / Left / Right / Test Pattern Enable)
(Top / Bottom / Left / Right / Test Pattern Enable)
Image Alignment
Corner Alignment
Top Left / Top Right / Bottom Left / Bottom Right /
Test Pattern Enable
Test Pattern Enable
Midpoint Alignment
Center / Top Middle / Left Middle / Right Middle /
Bottom Middle / Test Pattern Enable
Bottom Middle / Test Pattern Enable
Adjustment Mode
Both, Primary or Secondary
Splash Configure
Owner Name
ISF Calibrated
ISF Other
Splash Timer
ISF Calibrated
ISF Other
Splash Timer
5, 6, 7 ... 15 ... 59, 60
Splash Enable
On/Off
OSD Position
Hor. / Ver.
0, 1, 2 ... 100
Note: Default settings appear in bold type.