用户手册 — ADC AD-295

目录

• INTRODUCTION

  4
• Phase 5 Coin Microprocessor Controller (Computer) Features

  4
• L.E.D. DISPLAY AND CODES

  8
• OPERATING INSTRUCTIONS

  10
• A. Timed Mode

  10
• B. Automatic Mode (Patent No. 4,827,627)

  11
• C. Free Dry Mode

  12
• PROGRAM SELECTION

  13
• Temperature Display Mode

  13
• Right Coin Count (rCC)/Left Coin Count (LCC)

  13
• Automatic Review of Program Location

  14
• PL01 - Temperature Conversion Status

  15
• Automatic Mode (Auto) Patent No. 4,827,627

  15
• Timed Mode (tInE)

  15
• Anti-Wrinkle Program (Grd)

  16
• Buzz/Tone (bUZ)

  16
• Free Dry Mode Cycle (FrEE)

  16
• Coin Mode (Coin)

  17
• Flash Display Status (FLS)

  17
• Bad Coin Lockout Status (bCLO)

  17
• Bad Coin Reset (bCrS)

  17
• Accumulative Time (AtIn)

  18
• Accumulative Coin (ACOn)

  20
• Rotational Safe Guard - OPTIONAL (nSEn)

  21
• PL02 - Percent Dry (PdrY)

  21
• PL03 - High Temperature (HI° F)

  21
• PL04 - High Cool Down Temperature/Time (HIcd)

  22
• PL05 - Low Temperature (LO° F)

  22
• PL06 - Low Cool Down Temperature/Time (LOcd)

  22
• PL07 - Permanent Press (PP° F)

  22
• PL08 - Permanent Press Cool Down Temperature /Time (PPCd)

  22
• PL09 - Left Coin Slot Denomination (LCdE)

  22
• PL10 - Right Coin Slot Denomination (rCdE)

  23
• PL11 - Time For Amount To Start (tFAS)

  23
• PL12 - Amount To Start (AtSt)

  23
• PL13 - Minimum Amount For Additional Time (AFAT)

  23
• PL14 - Maximum Time For Automatic Dry (Adrt)

  23
• PL15 - Anti-Wrinkle Timing

  24
• Guard Delay Time (GdLY)

  24
• Guard On Time (Gont)

  24
• PL16 - Active Guard Time (AGt)

  24
• PL17 - “A” and “b” Factors

  24
• PROGRAMMING INSTRUCTIONS

  25
• A. Introduction To Programming

  25
• B. Programming (Flowcharts)

  26
• PROGRAMMING

  29
• Temperature Display Mode

  29
• Left Coin Count

  30
• Right Coin Count

  31
• Program Location 01 (PL01)

  32
• Program Location 02 (PL02)

  36
• Program Location 03 (PL03)

  37
• Program Location 04 (PL04)

  38
• Program Location 05 (PL05)

  39
• Program Location 06 (PL06)

  40
• Program Location 07 (PL07)

  41
• Program Location 08 (PL08)

  42
• Program Location 09 (PL09)

  43
• Program Location 10 (PL10)

  44
• Program Location 11 (PL11)

  45
• Program Location 12 (PL12)

  46
• Program Location 13 (PL13)

  47
• Program Location 14 (PL14)

  48
• Program Location 15 (PL15)

  49
• Program Location 16 (PL16) and Program Location 17 (PL17)

  50
• FACTORY PRESET PROGRAMS/PARAMETERS

  51
• For all dryer models except AD-26/AD-295 and AD-540/WDA-540

  52
• For all dryer models except AD-26/AD-295 and AD-540/WDA-540

  53
• For dryer models AD-26/AD-295 Only

  54
• For dryer models AD-26/AD-295 Only

  55
• PHASE 5 COIN SYSTEM DIAGNOSTICS

  56
• A. Diagnostic (L.E.D) Failure Codes

  56
• 1. “door”

  56
• 2. “dSFL”

  56
• 3. “SEFL”

  57
• 4. “Hot”

  57
• B. L.E.D. Display Indicators/Dots

  57
• 1. Heat Circuit Indicator

  57
• 2. Motor Circuit Indicator

  57
• C. Phase 5 Microprocessor Controller (Computer) Relay Output L.E.D. Indicators

  58
• 1. “DOOR”

  58
• 2. “HEAT”

  59
• 3. “MTR” (motor)

  59
• “A” AND “B” FACTOR PARAMETERS

  60
• OPTIONAL 9 VOLT BATTERY BACKUP

  62
• Settings: PL09 (LCdE)

  25
• PL11 (tFAS)

  30
• PL12 (AtSt)

  25
• Settings: PL09 (LCdE)

  25
• PL11 (tFAS)

  30
• PL12 (AtSt)

  50
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  15
• (AtSt)

  25
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  14
• (AtSt)

  35
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  33
• (AtSt)

  55
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  10
• (AtSt)

  35
• (LCdE)

  25
• (tFAS)

  24
• (AtSt)

  50
• (AFAt)

  50
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  20
• (AtSt)

  50
• (AFAt)

  20
• (LCdE)

  10
• (rCdE)

  25
• (tFAS)

  14
• (AtSt)

  35
• (AFAt)

  25