用户手册目录1. Getting started91.1 Safety Precautions91.2 Packing List91.3 Document Amendment History101.4 Manual Objectives111.5 System Specifications121.6 Architecture Overview14Block Diagram14Intel RG82855GME and FW82801DB (for ESM-2740)15Intel RG82852GM and FW82801DB (for ESM-2743)17DRAM Interface (Intel RG855GME)18DRAM Interface (Intel RG852GM)18Chrontel CH7011 TV Transmitter19PCI Interface19USB 2.019Ethernet20Winbond W83627HF20Winbond W83628F & W83629D PCI/ISA Bridge212. Hardware Configuration222.1 Product Overview232.2 Installation Procedure24Installing Processor24Main Memory26Jumper and Connector List28Setting Jumpers & Connectors29FSB Select (SW2)29ETX Connector X1 (ETXA)30Signal Description – ETX Connector X1 (ETXA)31ETX Connector X2 (ETXB)33Signal Description – ETX Connector X2 (ETXB)34ETX Connector X3 (ETXC)36Signal Description – ETX Connector X3 (ETXC)37ETX Connector X4 (ETXD)39Signal Description – ETX Connector X4 (ETXD)403. BIOS Setup433.1 Starting Setup44Using Setup45Getting Help46In Case of Problems46Main Menu47Standard CMOS Features48Advanced BIOS Features51Advanced Chipset Features55Integrated Peripherals59Power Management Setup63PnP / PCI Configuration65PC Health Status67Frequency / Voltage Control67Load Fail-Safe Defaults68Load Optimized Defaults68Set Supervisor / User Password69Save & Exit Setup70Exit Without Save714. Drivers Installation724.1 Install Chipset Driver (For Intel RG82855GME)734.2 Install Chipset Driver (For Intel RG82852GM)744.3 Install Display Driver (For Intel RG82855GME)754.4 Install Display Driver (For Intel RG82852GM)764.5 Install Audio Driver (For Intel 82801DB)774.6 Install Ethernet Driver (For Realtek RTL810x, RTL813x Family)785. Measurement Drawing79Appendix A: BIOS Revisions81Appendix B: AWARD BIOS POST Messages82Overview83Post Beep83Error Messages83CMOS BATTERY HAS FAILED83CMOS CHECKSUM ERROR83DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER83DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP83DISPLAY SWITCH IS SET INCORRECTLY84DISPLAY TYPE HAS CHANGED SINCE LAST BOOT84EISA Configuration Checksum Error PLEASE RUN EISA CONFIGURATION UTILITY84EISA Configuration Is Not Complete PLEASE RUN EISA CONFIGURATION UTILITY84ERROR ENCOUNTERED INITIALIZING HARD DRIVE84ERROR INITIALIZING HARD DISK CONTROLLER84FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT84Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY85KEYBOARD ERROR OR NO KEYBOARD PRESENT85Memory parity Error at85MEMORY SIZE HAS CHANGED SINCE LAST BOOT85OFFENDING ADDRESS NOT FOUND85OFFENDING SEGMENT:85PRESS A KEY TO REBOOT86PRESS F1 TO DISABLE NMI, F2 TO REBOOT86Should Be Empty But EISA Board Found PLEASE RUN EISA CONFIGURATION UTILITY86Should Have EISA Board But Not Found PLEASE RUN EISA CONFIGURATION UTILITY86Slot Not Empty86Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY87FLOPPY DISK(S) fail (80) → Unable to reset floppy subsystem87FLOPPY DISK(S) fail (40) → Floppy Type dismatch87Hard Disk(s) fail (80) → HDD reset failed87Hard Disk(s) fail (40) → HDD controller diagnostics failed87Hard Disk(s) fail (20) → HDD initialization error87Hard Disk(s) fail (10) → Unable to recalibrate fixed disk87Hard Disk(s) fail (08) → Sector Verify failed87Keyboard is locked out - Unlock the key.87Keyboard error or no keyboard present.87Manufacturing POST loop87BIOS ROM checksum error - System halted.87Memory test fail.87POST Codes88文件大小: 2.0 MB页数: 93Language: English打开用户手册