用户手册目录PRODUCT OVERVIEW81.1 INTRODUCTION81.2 TYPES OF AIS91.3 SYSTEM OVERVIEW101.4 REFERENCES111.5 ACRONYMS AND ABBREVIATIONS121.6 TECHNICAL SPECIFICATIONS141.6.1 Physical141.6.2 Environmental141.6.3 Electrical151.6.4 Data I/0 connections151.6.5 Display and user interface151.6.6 Internal GPS151.6.7 TDMA transmitter161.6.8 TDMA receivers161.6.9 DSC receiver16Interface sentences16BASIC PROTEC INSTALLATION172.1 INSTALLING THE PROTEC172.1.1 Mount the Transceiver and MKD182.1.2 Mount the Junction Box or Terminal Strip202.1.3 Connect Ships Sensors and Data Interfaces202.1.4 IEC Input / Output Electrical Characteristics222.1.5 Connect Power and Alarm Relay232.1.6 Install the VHF Antenna242.1.7 Connect the GPS Antenna262.1.8 Install the Pilot Port Cable (Optional)282.1.9 Apply Power and Configure the Transceiver29INPUT / OUTPUT CONNECTIONS303.1 CONNECTOR PART NUMBERS303.2 REAR PANEL CONNECTOR LOCATION303.2.1 IEC Data313.2.2 Power and BIIT323.2.3 VHF Antenna323.2.4 GPS Antenna333.2.5 NMEA 2000 (IEC 61162-3) CAN Bus333.2.6 Ethernet Lite (IEC 61162-450) data port343.2.7 One Pulse Per Second (1PPS)343.2.8 Discreet data and factory test connector353.3 FRONT PANEL CONNECTOR LOCATION363.3.1 Pilot Port36PROTEC OPERATION38FRONT PANEL DISPLAY AND CONTROLS394.1.1 Power On/Off394.1.2 Status Indictor Light394.1.3 Pilot Port394.1.4 Display394.1.5 Key Pad394.2 POWER-UP AND CONFIGURATION414.2.1 Power-Up the Transceiver414.2.2 Configure the Vessel Information into the PROTEC.414.3 VIEWING THE MENUS424.3.1 Main Menu424.3.2 Vessel Information444.3.3 Main System Menu454.3.4 Logon and Password Entry464.3.5 Entering System Information and Configuration Data484.3.6 Vessel / Voyage Information Setup504.3.7 Antenna Position Setup534.3.8 View Alarm Status564.3.9 View General Status58Down Time Log60Safety Text Log61Set AIS Channels62Channel Management62Changing the Password66Setting BAUD Rates67Set RS422 Termination Controls68Adjust Backlight Levels70Alarm Control Setup71Text Messaging73ANTENNAS75VHF75GPS77Figure 1- AIS Network8Figure 2 - AIS System with Flush Mount14Figure 3 - Remote MKD Shown With Flush and Trunnion Mounting17Figure 4 - Integrated MKD Shown With Flush and Trunnion Mounting18Figure 5 - AIS Interconnection Diagram (Optional interfaces not shown)19Figure 6 - IEC Data Cable21Figure 7 – A and B RS422 Signals22Figure 8 - IEC Data Cable External Wiring Diagram23Figure 9 - Sample Alarm Setup24Figure 10 - VHF Antenna Installation25Figure 11 - GPS Antenna Installation27Figure 12 - Pilot Port Cable28Figure 13 - Rear Panel Connector Location30Figure 14 - IEC Data Connector Pin Configuration31Figure 15 - Power and BIIT Connector Pin Configuration32Figure 16 - VHF SO239 Female Connector32Figure 17 - TNC Female Connector33Figure 18 - NMEA2000 CAN Bus M12 male A-coded Connector Pin-out33Figure 19 - Ethernet RJ-45 Connector Pin Configuration34Figure 20 - BNC Female Connector34Figure 21 - 15 Pin DSUB Female Configuration35Figure 22 - Front Panel Pilot Port36Figure 23 - Pilot Port Plug Configuration37Figure 24 - PROTEC Transceiver Front Panel38Figure 25 - Main Menu (Default Screen)42Figure 26 - Secondary Navigation Menu Showing Moving Targets43Figure 27 - Own Ship Information Menu44Figure 28 - Vessel Information Page 144Figure 29 - Vessel Information Page 245Figure 30 - Main System Menu46Figure 31 - System Password Entry Menu46Figure 32 - Password Entered47Figure 33 - System Information and Configuration Menu49Figure 34 - System Information and Configuration Screen49Figure 35 - Vessel / Voyage Menu51Figure 36 - Vessel / Voyage Screen51Figure 37 - Antenna Position Menu54Figure 38 - Antenna Position Screen54Figure 39 - Antenna Position Measurements55Figure 40 - Alarm Status Menu56Figure 41 - Alarm Status Screen56Figure 42 - General Status Menu58Figure 43 - General Status Screen58Figure 44 - Down Time Log Menu60Figure 45 - Down Time Log Screen61Figure 46 - Safety Text Log Menu61Figure 47 - Safety Text Log Screen62Figure 48 - Set AIS Channels Menu62Figure 49 - Set AIS Channels Screen62Figure 50 - Channel Management Menu63Figure 51 - Channel Management Screen63Figure 52 - Edit Mode Active Screen65Figure 53 - Save Settings Screen65Figure 54 - Change Password Menu66Figure 55 - Change Password Screen66Figure 56 - Set BAUD Rate Menu67Figure 57 - Set BAUD Rate Screen67Figure 58 - Set RS422 Termination Menu69Figure 59 - Set RS422 Termination Screen69Figure 60 - Adjust Backlight Level Menu70Figure 61 - Adjust Backlight Level Screen70Figure 62 - Alarm Control Menu71Figure 63 - Alarm Control Screen71Figure 64 - Alarm Acknowledged72Figure 65 - Safety Text Menu73Table 1 - Serial Data Ports Default Settings20Table 2- IEC Rear Panel Part Numbers30Table 3- IEC Data Connector Pin-out31Table 4 - Power and BITT Connector Pin-out32Table 5 - NMEA 2000 CAN Bus Connector Pin-out33Table 6 - Ethernet Connector Pin-out34Table 7 - Discreet data and factory test Pin-out35Table 8 - Pilot Port Pin-outs37Table 9 - PROTEC Default Passwords47Table 10 - Password Privileges According to Specific Menus48Table 11 - Type of Ship52Table 12 - Type of Ship (Continued)53Table 13 - Integrity Alarm Conditions Using ALR Sentence Formatter57文件大小: 2.2 MB页数: 79Language: English打开用户手册