数据表目录MCP1640/B/C/D - 0.65V Start-up Synchronous Boost Regulator with TrueOutput Disconnect or Input/Output Bypass Option11.0 Electrical Characteristics32.0 Typical Performance Curves5FIGURE 2-1: VOUT IQ vs. Ambient Temperature in PFM Mode.5FIGURE 2-2: VOUT IQ vs. Ambient Temperature in PWM Mode.5FIGURE 2-3: Maximum IOUT vs. VIN.5FIGURE 2-4: 2.0V VOUT PFM / PWM Mode Efficiency vs. IOUT.5FIGURE 2-5: 3.3V VOUT PFM / PWM Mode Efficiency vs. IOUT.5FIGURE 2-6: 5.0V VOUT PFM / PWM Mode Efficiency vs. IOUT.5FIGURE 2-7: 3.3V VOUT vs. Ambient Temperature.6FIGURE 2-8: 3.3V VOUT vs. Ambient Temperature.6FIGURE 2-9: 3.3V VOUT vs. VIN.6FIGURE 2-10: Minimum Start-up and Shutdown VIN into Resistive Load vs. IOUT.6FIGURE 2-11: FOSC vs. Ambient Temperature.6FIGURE 2-12: PWM Pulse Skipping Mode Threshold vs. IOUT.6FIGURE 2-13: Input No Load Current vs. VIN.7FIGURE 2-14: N-Channel and P-Channel RDSON vs. > of VIN or VOUT.7FIGURE 2-15: PFM / PWM Threshold Current vs. VIN.7FIGURE 2-16: MCP1640 3.3V VOUT PFM Mode Waveforms.7FIGURE 2-17: MCP1640B 3.3V VOUT PWM Mode Waveforms.7FIGURE 2-18: MCP1640/B High Load Waveforms.7FIGURE 2-19: 3.3V Start-up After Enable.8FIGURE 2-20: 3.3V Start-up when VIN = VENABLE.8FIGURE 2-21: MCP1640 3.3V VOUT Load Transient Waveforms.8FIGURE 2-22: MCP1640B 3.3V VOUT Load Transient Waveforms.8FIGURE 2-23: MCP1640B 2.0V VOUT Load Transient Waveforms.8FIGURE 2-24: 3.3V VOUT Line Transient Waveforms.83.0 Pin Descriptions9TABLE 3-1: Pin Function Table93.1 Switch Node Pin (SW)93.2 Ground Pin (GND)93.3 Enable Pin (EN)93.4 Feedback Voltage Pin (FB)93.5 Output Voltage Pin (VOUT)93.6 Power Supply Input Voltage Pin (VIN)93.7 Signal Ground Pin (SGND)93.8 Power Ground Pin (PGND)93.9 Output Voltage Sense Pin (VOUTS)93.10 Output Voltage Power Pin (VOUTP)93.11 Exposed Thermal Pad (EP)94.0 Detailed Description114.1 Device Option Overview11TABLE 4-1: Part Number Selection114.2 Functional Description12FIGURE 4-1: MCP1640/B/C/D Block Diagram.125.0 Application Information155.1 Typical Applications155.2 Adjustable Output Voltage Calculations155.3 Input Capacitor Selection155.4 Output Capacitor Selection15TABLE 5-1: Capacitor Value Range155.5 Inductor Selection16TABLE 5-2: MCP1640/B/C/D Recommended Inductors165.6 Thermal Calculations165.7 PCB Layout Information16FIGURE 5-1: MCP1640/B/C/D SOT23-6 Recommended Layout.17FIGURE 5-2: MCP1640/B/C/D DFN-8 Recommended Layout.176.0 Typical Application Circuits19FIGURE 6-1: Manganese Lithium Coin Cell Application Using Bypass Mode.19FIGURE 6-2: USB On-The-Go Powered by Li-Ion.197.0 Packaging Information217.1 Package Marking Information21Appendix A: Revision History27Product Identification System29Worldwide Sales and Service32文件大小： 476.8 KB页数： 32Language: English打开用户手册
数据表目录Preface5Introduction5Document Layout5Conventions Used in this Guide6Recommended Reading7The Microchip Web Site7Customer Support7Document Revision History7Chapter 1. Product Overview91.1 Introduction91.2 MCP1640 Short Overview91.3 What Is the MCP1640 Single Quadruple-A Battery Boost Converter Reference Design?101.4 MCP1640 Single Quadruple-A Battery Boost Converter Reference Design Kit Contents10Chapter 2. Installation and Operation112.1 Introduction112.2 Getting Started13Appendix A. Schematic and Layouts17A.1 Introduction17A.2 Board – Schematic18A.3 Board – Top Silk And Pads19A.4 Board – Top Trace And Pads19A.5 Board – Bottom Silk Layer19A.6 Board – Bottom Trace, Pads And Silk19Appendix B. Bill of Materials21Appendix C. MCP1640 Single Quadruple-A Battery Boost Converter Reference Design Firmware23C.1 Device Firmware23Worldwide Sales28文件大小： 498.7 KB页数： 28Language: English打开用户手册
