用户手册 — Murata Electronics North America HN1010

目录

• Overview

  1
• INTRODUCTION

  1
• HOPNET PRODUCTS

  1
• External Antenna

  1
• Built-In Antenna

  1
• Accessories

  1
• DESIGN FEATURES

  1
• GLOSSARY OF TERMS

  2
• About HopNet Products

  5
• INTRODUCTION

  5
• OPERATING FREQUENCY

  5
• HOPNET FREQUENCY HOPPING SPREAD SPECTRUM ADVANTAGES

  5
• HOPNET DATA INTEGRITY

  5
• FLEXIBLE POWER MANAGEMENT

  5
• HN-1010 Outdoor Base/Remote Station

  7
• INTRODUCTION

  7
• DATA TRANSMISSION

  7
• JUMPER SETTINGS

  8
• POWER CONNECTION

  8
• ANTENNA CONNECTION

  8
• TECHNICAL SPECIFICATIONS

  10
• General

  10
• Mechanical

  11
• Environmental

  11
• HN-1510 Outdoor Base/Remote Station

  13
• INTRODUCTION

  13
• DATA TRANSMISSION

  13
• LED STATUS

  14
• POWER CONNECTION

  14
• ANTENNA CONNECTION

  14
• TECHNICAL SPECIFICATIONS

  15
• General

  15
• Mechanical

  16
• Environmental

  16
• HN-3500 Adapter

  17
• INTRODUCTION

  17
• FLOW CONTROL INDICATORS

  18
• DB-9 CONNECTOR

  18
• TERMINAL BLOCK

  18
• TERMINAL BLOCK

  19
• POWER SUPPLY

  21
• Introduction

  21
• AC to DC Conversion

  21
• Alternate Power Sources

  21
• Configuring the Network

  23
• OVERVIEW

  23
• Introduction

  23
• Five Command Types

  23
• INSTALLING THE WINCOM24 SOFTWARE

  24
• MODEM COMMANDS

  25
• SERIAL COMMANDS

  26
• Set Data Rate Divisor

  26
• Set Protocol Mode

  27
• NETWORK COMMANDS

  28
• Set Transceiver Mode

  28
• Set Default Handle

  28
• Enable Global Network Mode

  29
• Set Hopping Pattern

  29
• Set Transmit Power

  29
• Read Receive Signal Strength Indicator (RSSI)

  29
• Set Range Optimization

  30
• PROTOCOL COMMANDS

  31
• Set Alternative Frequency Band

  32
• Set Hop Duration

  32
• Set Minimum Data Length

  32
• Get Maximum Data Length (read only)

  32
• Set Maximum Number of Remotes (base only)

  33
• Set Packet Attempts Limit

  33
• Set Data Transmit Delay

  33
• Set Slot Assignment Mode (base station only)

  33
• Set Base Slot Size (base station only)

  34
• Set ARQ Mode

  34
• STATUS COMMANDS

  35
• Banner Display Disable

  35
• Set Escape Sequence Mode

  35
• Read Factory Serial Number High, Middle and Low Bytes.

  36
• Set Duty Cycle

  36
• Enable Low Power Acquisition Mode

  36
• MEMORY COMMANDS

  37
• Recall Factory Defaults

  37
• Recall Memory

  37
• Store Memory

  37
• MODEM COMMAND SUMMARY

  38
• GUIDELINES FOR INSTALLATION

  39
• Typical HopNet Applications

  41
• INTRODUCTION

  41
• POINT TO MULTIPOINT

  41
• POINT-TO-POINT

  42
• Troubleshooting

  43
• OVERVIEW

  43
• Introduction

  43
• Transceiver Requirements

  43
• COMMON SYSTEM PROBLEMS

  44
• GUIDELINES FOR REDUCING INTERFERENCE

  45
• Introduction

  45
• Guidelines for Setting Up the Network

  45
• Guidelines for Selecting Your Site

  45
• GUIDELINES FOR AVOIDING TERRAIN OBSTRUCTIONS

  46
• CUSTOMER SUPPORT

  47
• Introduction

  47
• Technical Assistance

  47
• Factory Repairs

  47
• Warranty

  48
• Notes:

  49