用户手册目录Getting Started with YourGPIB-SCSI-A and NI-488.2™ for Solaris1Support2Worldwide Technical Support and Product Information2National Instruments Corporate Headquarters2Worldwide Offices2Important Information3Warranty3Copyright3Trademarks3Patents3WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS3Compliance4Conventions6Contents7Chapter 1 Introduction9What You Need to Get Started9GPIB Hardware Overview10NI-488.2 Overview10Chapter 2 Installation11Figure 2-1. GPIB-SCSI-A Rear Panel11Configuring the Hardware11Configuration Switch Settings for SW112Figure 2-2. SW1 Default Mode Switch Settings12Table 2-1. SW1 Configuration Parameters for Switches 1 through 313Table 2-2. SW1 Configuration Parameters for Switches 4 through 813Configuration Switch Settings for SW215Figure 2-3. SW2 Default Mode Switch Settings15Table 2-3. Factory Default Configurations for SW215Using SCSI Terminating Resistors16Figure 2-4. Location of Terminating Resistors for GPIB-SCSI-A at End of SCSI Bus17Figure 2-5. Location of Terminating Resistors for GPIB-SCSI-A Not at End of SCSI Bus18Connecting the Hardware18Step 1. Shut Down the System19Step 2. Connect the Cables19Step 3. Switch On Your GPIB-SCSI-A20Step 4. Power On Your System20Installing NI-488.220Configuring the Software with ibconf (Optional)21Removing NI-488.2 (Optional)21Chapter 3 Installation Verification22Chapter 4 Using NI-488.2 with Solaris23Introduction to ibic23Programming Considerations24Appendix A Troubleshooting and Common Questions25Appendix B Specifications28Appendix C Technical Support Resources30Glossary32Index34C-I34K-W35文件大小: 998.9 KB页数: 35Language: English打开用户手册
用户手册目录Getting Started with YourGPIB-SCSI-A and NI-488.2™ for Solaris1Support2Worldwide Technical Support and Product Information2National Instruments Corporate Headquarters2Worldwide Offices2Important Information3Warranty3Copyright3Trademarks3Patents3WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS3Compliance4Conventions6Contents7Chapter 1 Introduction9What You Need to Get Started9GPIB Hardware Overview10NI-488.2 Overview10Chapter 2 Installation11Figure 2-1. GPIB-SCSI-A Rear Panel11Configuring the Hardware11Configuration Switch Settings for SW112Figure 2-2. SW1 Default Mode Switch Settings12Table 2-1. SW1 Configuration Parameters for Switches 1 through 313Table 2-2. SW1 Configuration Parameters for Switches 4 through 813Configuration Switch Settings for SW215Figure 2-3. SW2 Default Mode Switch Settings15Table 2-3. Factory Default Configurations for SW215Using SCSI Terminating Resistors16Figure 2-4. Location of Terminating Resistors for GPIB-SCSI-A at End of SCSI Bus17Figure 2-5. Location of Terminating Resistors for GPIB-SCSI-A Not at End of SCSI Bus18Connecting the Hardware18Step 1. Shut Down the System19Step 2. Connect the Cables19Step 3. Switch On Your GPIB-SCSI-A20Step 4. Power On Your System20Installing NI-488.220Configuring the Software with ibconf (Optional)21Removing NI-488.2 (Optional)21Chapter 3 Installation Verification22Chapter 4 Using NI-488.2 with Solaris23Introduction to ibic23Programming Considerations24Appendix A Troubleshooting and Common Questions25Appendix B Specifications28Appendix C Technical Support Resources30Glossary32Index34C-I34K-W35文件大小: 998.9 KB页数: 35Language: English打开用户手册