用户手册 — Netgear WNDAP360 - ProSAFE Dual Band Wireless-N Access point

目录

• ProSAFE Dual Band Wireless-N Access Point WNDAP360

  1
• Contents

  3
• 1. Introduction

  6
  • About the ProSAFE Dual Band Wireless-N Access Point WNDAP360

    6
  • What Is In the Box?

    7
  • System Requirements

    7
  • Key Features and Standards

    8
    • Supported Standards and Conventions

      8
    • Key Features

      9
    • 802.11b/g/n and 802.11a/n Standards–Based Wireless Networking

      10
    • Autosensing Ethernet Connections with Auto Uplink

      10
  • Hardware Description

    11
    • Top Panel

      11
    • Rear Panel

      12
    • Bottom Panel with Product Label

      13
• 2. Installation and Basic Configuration

  14
  • What You Need before You Begin

    14
    • Wireless Equipment Placement and Range Guidelines

      14
    • Ethernet Cabling Requirements

      15
    • LAN Configuration Requirements

      15
    • Computer Hardware Requirements

      15
  • Install and Configure the Wireless Access Point

    15
    • Connect the Wireless Access Point to Computer

      16
    • Log In to the Wireless Access Point

      17
    • Configure Basic General System Settings and Time Settings

      19
    • Configure IP Settings and Optional DHCP Server Settings

      21
    • Configure Basic Wireless Settings

      23
    • Operating Frequency (Channel) Guidelines

      29
  • Test Basic Wireless Connectivity

    30
  • Mount the Wireless Access Point

    30
    • Ceiling Installation

      31
    • Wall Installation

      33
    • Desk Installation

      35
• 3. Wireless Configuration and Security

  36
  • Wireless Data Security Options

    36
  • Security Profiles

    38
    • Before You Change the SSID, WEP, and WPA Settings

      39
    • Configure and Enable Security Profiles

      42
  • Configure RADIUS Server Settings

    51
  • Restrict Wireless Access by MAC Address

    53
  • Schedule the Wireless Radio to Be Turned Off

    55
  • Configure Basic Wireless Quality of Service

    56
• 4. Management

  58
  • Enable Remote Management

    58
    • SNMP Management

      59
    • Secure Shell and Telnet Management

      60
  • Upgrade the Wireless Access Point Software

    61
  • Manage the Configuration File or Reset to Factory Defaults

    64
    • Save the Configuration

      64
    • Restore the Configuration

      65
    • Restore the Wireless Access Point to the Factory Default Settings

      66
    • Reboot the Wireless Access Point without Restoring the Default Configuration

      67
  • Change the Administrator Password

    68
  • Enable the Syslog Server

    69
  • Monitor the Wireless Access Point

    69
    • View System Information

      70
    • Monitor Wireless Stations

      72
    • View the Activity Log

      75
    • Traffic Statistics

      75
  • Enable Rogue AP Detection and Monitor Access Points

    77
    • Enable and Configure Rogue AP Detection

      77
    • View and Save Access Point Lists

      79
• 5. Advanced Configuration

  81
  • Spanning Tree Protocol and 802.1Q VLAN

    81
  • Hotspot Settings

    83
  • Configure Advanced Wireless Settings

    84
  • Configure Advanced QoS Settings

    86
  • Configure Wireless Bridging

    89
    • Configure a Point-to-Point Wireless Network

      90
    • Configure a Point-to-Multipoint Wireless Network

      93
    • Configure the Wireless Access Point to Repeat the Wireless Signal Using Point-to-Multipoint Bridge Mode

      98
• 6. Troubleshooting

  103
  • Basic Functioning

    104
    • No LEDs Are Lit on the Wireless Access Point

      104
    • The Active LED or the LAN LED Is Not Lit

      105
    • The WLAN LED Does Not Light Up

      105
  • You Cannot Access the Internet or the LAN from a Wireless-Capable Computer

    105
  • You Cannot Configure the Wireless Access Point from a Browser

    106
  • When You Enter a URL or IP Address a Time-Out Error Occurs

    107
  • Troubleshooting a TCP/IP Network Using the Ping Utility

    107
    • Testing the LAN Path to Your Wireless Access Point

      107
    • Testing the Path from Your Computer to a Remote Device

      108
  • Problems with Date and Time

    108
  • Use the Packet Capture Tool

    109
• A. Supplemental Information

  110
  • Technical Specifications

    110
  • Factory Default Settings

    112
• B. Command-Line Reference

  115
• Index

  128