用户手册 — Roberts Gorden 10081601NA Rev H 12/11

目录

• SECTION 1: Introduction

  2
• SECTION 7: Variable Frequency Drive Programming

  42
• 1.1 Safety

  2
• 1.2 What is ROBERTS GORDON® ULTRAVAC™?

  2
• GORDON® ULTRAVAC™

  42
• 1.3 General Requirements

  2
• 7.2 Altering VFD Parameters

  43
• 1.4 CORAYVAC® Design Requirements

  2
• 1.5 Example Site Layout

  3
• 8.1 Setting The CORAYVAC® End Burner Vacuum

  44
• 1.6 Check Installation Materials

  3
• SECTION 9: Troubleshooting

  48
• 1.7 Safety Labels and Their Placement

  3
• SECTION 10: Replacement Parts

  55
• 1.8 Carton Contents

  10
• 1.9 Standard Parts List

  13
• Replacement Parts

  56
• SECTION 2: Specifications

  16
• 10.2 Variable Frequency Drive Replacement Parts

  57
• 2.1 ROBERTS GORDON® ULTRAVAC™ Controller

  16
• 2.2 ULTRAVAC™ BMS Link Controller

  16
• Parts

  58
• 2.3 NEMA 4 Enclosure (P/N 10080302)

  16
• 10.4 Repeater Replacement Parts

  59
• 2.4 Repeater

  16
• 10.5 Replacement Parts Instructions

  60
• 2.5 Temperature Sensors

  16
• 2.6 Line Reactor 480 V / 4 A Output

  17
• Warranty

  62
• 2.7 Variable Frequency Drive (VFD)

  19
• SECTION 3: Installation

  21
• 3.1 Preparation

  21
• Controller and Variable Frequency Drive

  21
• 3.3 Cable Requirements:

  22
• Controller

  22
• 3.5 Pump Requirements

  23
• 3.6 Variable Frequency Drive Requirements

  23
• 3.7 Indoor Sensor Placement

  24
• 3.8 Outdoor Sensor Placement

  24
• 3.9 Outside Air Supply

  24
• SECTION 4: Typical External Diagrams

  25
• SECTION 5: Communications

  30
• 5.2 RS-485 Converter for Central Controller

  31
• 5.3 TCP/IP Communication Module

  32
• 5.4 Direct Connect

  33
• GORDON® ULTRAVAC™ Controllers

  35
• SECTION 6: ULTRAVAC™ BMS Link Controller

  38
• 6.1 ULTRAVAC™ BMS Link Controller Overview

  38
• 6.2 ULTRAVAC™ BMS Link Controller Requirements

  39
• 6.3 Technical Data

  40
• 6.4 ULTRAVAC™ BMS Link Controller Programming

  40
• Figure 1: ULTRAVAC™ Controller Label Placement

  4
• Figure 3: VFD Label Placement

  6
• Figure 4: Repeater Label Placement

  7
• Figure 5: Connected Components

  8
• Figure 6: Example Site Layout

  15
• Specifications

  18
• (Factory pre-wiring shown)

  20
• Figure 9: Controller Mounting

  21
• Figure 10: Variable Frequency Drive Mounting

  23
• Figure 11: Indoor Sensor Mounting

  24
• Figure 12: Outdoor Sensor Placement

  24
• Controller External Wiring

  26
• Controller External Wiring

  28
• Figure 15: Modem Location

  30
• Figure 16: RS-485 PC Connection

  31
• Figure 17: TCP/IP Communication Module Mounting

  32
• Figure 18: TCP/IP Communication Module Wiring

  33
• Figure 19: 9 Pin Adapter for PC

  34
• Figure 20: Communications Between Multiple Controllers

  35
• Figure 21: Repeater External Wiring

  36
• Controllers

  37
• Figure 23: Standard ULTRAVAC™ BMS Link Architecture

  38
• Figure 24: ULTRAVAC™ BMS Link Controller Schematic

  39
• Figure 26: End Vent Vacuum

  45
• Figure 27: Possible Damper Couplings’ Locations

  46
• Figure 28: Troubleshooting Flow Chart

  49
• Figure 29: Troubleshooting Flow Chart - Repeater

  53
• Figure 30: Troubleshooting Flow Chart - BACnet®

  54
• Components Diagram

  56
• Diagram

  58
• Figure 34: Repeater Components Diagram

  59