用户手册 — Sun Microsystems FC-100

目录

• Sun™ StorEdge™ FC-100 Hub Installation and Service Manual

  1
  • Formerly the Sun™ Enterprise Network Array™

    1
  • Regulatory Compliance Statements

    3
    • FCC Class A Notice

      3
    • FCC Class B Notice

      3
    • DOC Class A Notice - Avis DOC, Classe A

      4
    • DOC Class B Notice - Avis DOC, Classe B

      4
• Declaration of Conformity

  11
  • EMC

    11
    • European Union-EC

      11
  • Safety

    11
  • Supplementary Information

    11
• Contents

  13
  • 1. Product Description11

    13
  • 2. Installation21

    13
  • 3. Service31

    13
  • A. SpecificationsA1

    14
    • Preface

      15
• Using UNIX Commands

  15
• Typographic Conventions

  16
  • TABLEP1 Typographic Conventions

    16
• Shell Prompts

  16
  • TABLEP2 Shell Prompts

    16
• Related Documentation

  17
• Sun Documentation on the Web

  17
• Sun Welcomes Your Comments

  17
  • Product Description

    19
• 1.1 Sun StorEdge FC100 Hub

  19
  • FIGURE11 Front of Hub

    20
  • FIGURE12 Rear of Hub

    20
• 1.2 GBIC

  21
  • FIGURE13 GBIC That Does Not Have a Bail

    21
  • FIGURE14 GBIC That Has a Bail

    21
  • Installation

    23
• 2.1 Inspecting the Hub

  23
  • 1. Unpack the hub.

    23
  • 2. Inspect the hub for evidence of damage.

    23
  • 3. Save the packing materials for future use.

    23
• 2.2 Rackmount Placement

  23
• 2.3 Installing the Hub

  24
  • 2.3.1 Tools You Will Need

    24
  • 2.3.2 Preparing the Cabinet

    24
  • 2.3.3 Installing the Mounting Tray in the Cabinet

    24
    • 1. Select the correct mounting holes in the cabinet to use for the tray.

      24
    • 2. Install the tray in the cabinet (FIGURE21).

      25
      • FIGURE21 Installing the Tray in the Cabinet

        25
      • a. In the front of the tray, use the Phillips screwdriver to loosely install two 10-32 screws eac...

        25
      • b. In the back of the tray, use the Phillips screwdriver to loosely install two 10-32 screws each...

        25
      • c. Tighten both sets of screws.

        25
  • 2.3.4 Installing the Hub on the Mounting Tray

    26
    • 1. Determine on which side of the tray you are going to install the hub.

      26
    • 2. From the rear of the tray, slide the hub mounting bracket into the slots in the mounting tray ...

      26
      • FIGURE22 Installing the Hub on a Mounting Tray

        26
  • 2.3.5 Installing GBICs and Fiber Optic Cables

    27
    • 1. Choose the hub port into which you will install the GBIC.

      27
    • 2. Insert the GBIC into the port.

      27
      • FIGURE23 Installing a GBIC and Fiber Optic Cable

        27
      • FIGURE24 Installing a GBIC That Has a Bail and Fiber Optic Cable

        28
    • 3. Connect the fiber optic cable to the GBIC.

      28
    • 4. Route the fiber optic cable to an initiator or target.

      28
    • 5. Connect the fiber optic cable to a GBIC in the initiator or target.

      28
  • 2.3.6 Routing the Power Cord

    28
    • 1. Connect the female end of the power cord to the power receptacle at the rear of the hub (FIGUR...

      29
    • 2. Route the power cord down the right side and along the bottom of the cabinet.

      29
    • 3. Route the power cord up through the cutout to the power distribution unit at the left side of ...

      29
    • 4. Connect the power cord for the tray to the power distribution unit.

      29
    • 5. Tuck the extra length of the power cord down into the pocket beneath the power distribution unit.

      29
  • 2.3.7 Verifying the Configuration

    29
    • 1. Power on all nodes and then the hub.

      29
    • 2. Make sure that the Device Active LEDs are lit for active hub ports.

      29
  • 2.3.8 Reassembling the Cabinet

    30
• 2.4 Troubleshooting

  30
  • TABLE21 Troubleshooting

    30
  • Service

    31
• 3.1 Installing a GBIC

  31
  • 1. Choose the hub port into which you will install the GBIC.

    31
  • 2. Insert the GBIC into the port.

    31
    • FIGURE31 Installing a GBIC That Does Not Have a Bail

      32
    • FIGURE32 Installing a GBIC That Has a Bail

      33
  • 3. Connect the fiber optic cable to the GBIC.

    33
• 3.2 Removing a GBIC

  34
  • 1. Disconnect the fiber optic cable from the GBIC (FIGURE33 or FIGURE34).

    34
  • 2. Remove the GBIC.

    34
    • FIGURE33 Removing a GBIC That Does Not Have a Bail

      34
    • FIGURE34 Removing a GBIC That Has a Bail

      35
• 3.3 Removing a Hub

  36
  • 1. Disconnect and remove any installed fiber optic cables or GBICs (FIGURE33).

    36
  • 2. Disconnect the AC power cord from the hub.

    36
  • 3. Push up on the retaining tab that secures the hub to the mounting tray (FIGURE35).

    36
    • FIGURE35 Removing the Hub

      36
  • 4. Pull the hub back and then lift it out of the mounting slots.

    36
  • A

    37
  • Specifications

    37
• A.1 Physical

  37
  • TABLEA1 Physical Specifications

    37
• A.2 Electrical

  38
  • TABLEA2 Electrical Specifications

    38
• A.3 Environmental

  38
  • TABLEA3 Environmental Specifications

    38