用户手册目录SAFETY MESSAGES2TABLE OF CONTENTS3LIST OF FIGURES7LIST OF TABLES8HOW TO USE THIS MANUAL11GETTING STARTED13Installation13Electrical and Pneumatic Connections14Initial Operation19SPECIFICATIONS, AGENCY APPROVALS, WARRANTY27Specifications27Warranty28THE M100AH SO2 ANALYZER31Principle of Operation31Instrument Description33Sensor Module, Reaction Cell, Detector33Pneumatic Sensor Board33Computer Hardware and Software33V/F Board34Front Panel34Front Panel Display36Status LED's36Power Switch37Power Supply Module37Pneumatic System37I/O Hardware Interface38RS-232 Interface38RS-232 Connection Examples40RS-232 Diagnostic Procedures40Status Output Interface41Contact Closure Control Input Interface43SOFTWARE FEATURES45Index To Front Panel Menus45Sample Menu47Set-Up Menu48Sample Mode51Test Functions51CAL, CALS, CALZ, Calibration Functions54CAL, CALS, CALZ54Zero54Span54SO2 Cal Concentration55Formula Values55Set-Up Mode56Configuration Information (CFG)56Automatic Calibration (AutoCal)56Data Acquisition System (DAS)56Data Channels56RS-232 Reporting58Range Menu59Single Range59Auto Range60Dual Ranges60Concentration Units61Password Enable62Time of Day Clock62Diagnostic Mode62Communications Menu62Variables Menu (VARS)63OPTIONAL HARDWARE AND SOFTWARE65Rack Mount Options65Zero/Span Valves65Autocal - Setup Zero/Span Valves664-20 mA, Isolated Current Loop Output70RS-232 INTERFACE71Setting Up the RS-232 Interface71Setup from the Front Panel71Security Feature72Protocol of Port Communication73Entering Commands in Terminal Mode74Command Summary75TEST Commands and Messages78WARNING Commands and Messages79CALIBRATION Commands and Messages81DIAGNOSTIC Commands and Messages83DAS Commands and Reports84VARIABLES Commands and Messages86CALIBRATION AND ZERO/SPAN CHECKS89Manual Zero/Span Check or Calibration Through the Sample Port91Manual Zero/Span Check or Calibration with Zero/Span Valves Option93Automatic Zero/Span Check94Dynamic Zero/Span Calibration94Use of Zero/Span Valves with Remote Contact Closure94Special Calibration Requirements for Dual Range or Auto Range95Calibration Quality96Calibration Gases97MAINTENANCE99Maintenance Schedule99Replacing the Sample Particulate Filter100Replacing the Pump Scrubber102Cleaning Orifice and Orifice Filter102Cleaning the Reaction Cell103Pneumatic Line Inspection103Leak Check Procedure105Light Leak Check Procedure107EPROM Replacement Procedure108DIAGNOSTIC, TROUBLESHOOTING109Operation Verification - M100AH Diagnostic Techniques111Fault Diagnosis with TEST Variables111Fault Diagnosis with WARNING Messages117Fault Diagnosis using DIAGNOSTIC Mode119Signal I/O Diagnostic121Electric Test124Optic Test125Analog Out Step Test125DAC Calibration126RS-232 Port Test126M100AH Internal Variables126Test Channel Analog Output128Factory Calibration Procedure (Quick Cal)129Electric Test (ET) Procedure130Optic Test (OT) Procedure130Performance Problems131AC Power Check131Flow Check132No Response to Sample Gas132Negative Concentration Display133Excessive Noise133Unstable Span134Unstable Zero134Inability to Span135Inability to Zero135Non-Linear Response136Slow Response136Analog Output Doesn't Agree with Display Concentration136Electronic Subsystem Troubleshooting and Adjustments137Computer, Display, Keyboard137Front Panel Display137Single Board Computer138Front Panel Keyboard139Voltage/Frequency (V/F) Board141ADC/DAC Calibration Procedure143Changing Output Voltage Ranges144Status/Temp Board146Temperature Amplifier Section146Display Brownout147Status Output Lines, External Contact Closures1474-20 mA Current Output148Power Supply Module149PSM Diagnostic Procedures152Flow/Pressure Sensor153Reaction Cell Temp157Preamp Board157PMT Cooler158HVPS (High Voltage Power Supply)160Optical Sensor Module Troubleshooting162PMT162UV Lamp Adjust or Replacement162Pneumatic System Troubleshooting164Leak Check164Pump164Z/S Valves164M100AH SPARE PARTS LIST165Model 100AH Level 1 Spares Kit167MAINTENANCE SCHEDULE FOR M100AH169ELECTRICAL SCHEMATICS171文件大小: 2.7 MB页数: 172Language: English打开用户手册