用户手册目录Limited Warranty4What does this warranty cover and how long does it last?4What will Xantrex do?4How do you get service?4What does this warranty not cover?5Disclaimer6Exclusions6Information7WARNING: Limitations on Use7Information About Your Power Supply7Release7Warnings and Cautions8Power Supply Safety8About This Manual9Main Sections9Section1 Features and Specifications9Section2 Installation and Configuration9Section3 Operation9Manual Revisions9Contents11Section 1. Features and Specifications11Section 2. Installation and Configuration11Section 3. Operation11Section 1. Features and Specifications13Description13Features13Specifications13Section 2. Installation and Configuration15Introduction15Initial Inspection15Configuring16Front panel16Figure 2.1 XT/HPD Front Panel with APG Interface Installed16Rear Panel17Figure 2.2 XT/HPD Rear Panel with APG Interface17Rear Panel Switch (S1) Defaults17Rear Panel J5 Connector18J5 Connector Pin Assignments18Calibration Adjustment19Figure 2.3 APG Interface Calibration Adjustment Locations19Section 3. Operation21Remote Programming21Programming Output Voltage with a 010Vdc Voltage Source211. Select remote voltage programming by moving the rear panel switch S15 (remote voltage program...212. Connect the voltage source between pin17 (voltage program) and either pin4 or pin5 (program...213. Vary the external voltage from 010Vdc to cause the power supply output to vary from 0100% of...22Programming Output Voltage with a 010k Resistance221. Select remote voltage programming by moving the rear panel switch S15 (remote voltage program...222. Set rear panel switch S14 (resistive voltage program select) to the ON (closed) position.223. Connect a variable resistor between pin17 (voltage program) and either pin4 or pin5 (progra...224. Adjust the resistance from 010kW to vary the power supply output from 0100% of rated output ...22Programming Output Current with a 0-10 Vdc Voltage Source221. Select remote current limit programming by moving the rear panel switch S13 (remote current p...222. Connect the voltage source between J5 pin16 (current program, positive) and either pin4 or p...223. Vary the external voltage from 010Vdc to cause the power supply current limit to vary from 0...22Programming Output Current with a 0-10k Resistance231. Select remote current programming by external resistance by moving the rear panel switch S13 ...232. Set rear panel switch S12 (resistive current program select) to the ON (closed) position.233. Connect a variable resistance between J5 pin16 and either pin4 or pin5 (program return).234. Adjust the resistance from 010kW to vary the power supply current limit from 0100% of rated ...23Programming with a Fixed +10V Reference231. Connect resistor A between J5 connector pin 20 (+10V reference out) and pin 17 (voltage progr...232. Connect resistor B between pin 17 (voltage program) and either pin 4 or 5 (program return).23Figure 3.1 Programming with a Fixed +10V Reference23Readback and Status Indicators24Voltage and Current Readback24Voltage Readback24Current Readback24Operating Mode Status24Remote Programming Status24Output Fail Flag24Overvoltage Protection (OVP)25OVP Flag25Setting the OVP Trip Level251. Turn the power supply OFF.252. Insert a small, flatbladed screwdriver through the OVP ADJ (OVP Adjust) hole in the front pan...253. Turn the unit ON and set the output to the desired trip voltage.254. Slowly turn the adjusting screw counterclockwise until the red OVP indicator lamp lights.255. Turn the POWER switch to OFF.256. Turn the voltage control knob to minimum.257. Turn the POWER switch back ON and increase the voltage to check that the power supply shuts of...258. Reset the OVP circuit after activation by removing the overvoltage condition and powering the ...25TTL Shutdown26Tracking271. Master/slave power supplies must have the same output ratings.272. Set switch S2 on the slave unit's APG InterfacePCB to the correct model number (factory prese...273. Slave tracking can be calibrated by adjusting the unit's offset and range potentiometers. See ...274. As the slave is referenced to the master's output, the noise and ripple on the slave may incre...27Figure 3.2 Master/Slave Tracking Configuration27文件大小： 308.0 KB页数： 30Language: English打开用户手册
