Sony Security Camera Benutzerhandbuch
Installation
15
Note
The default IP address for LAN port 1 is follows;
• LAN connector 1: 192.168.0.1
• LAN connector 2: 192.168.1.1
• LAN connector 1: 192.168.0.1
• LAN connector 2: 192.168.1.1
(only the NSR-100/50)
• LAN connector 3: 192.168.2.1
(only the NSR-100/50)
If you want to change the default IP address, refer to the
“User’s Guide” (PDF) on the supplied “NSR Series
Manual, Tool & Source Codes CD”.
“User’s Guide” (PDF) on the supplied “NSR Series
Manual, Tool & Source Codes CD”.
Connecting a Network Camera
Use a network cable to connect LAN connector 1 to a
network switch, and then connect the desired network
camera to the network switch with another network
cable.
network switch, and then connect the desired network
camera to the network switch with another network
cable.
Connecting Other Devices
Using a CompactFlash Card (Only the
NSR-100/50)
NSR-100/50)
Insert your CompactFlash card in the direction
illustrated. Make sure that you insert your card with the
label side facing up and in the direction of the arrow.
illustrated. Make sure that you insert your card with the
label side facing up and in the direction of the arrow.
When ejecting a CompactFlash card, press the eject
button on the left of the card slot.
button on the left of the card slot.
Caution
Be careful when ejecting a CompactFlash card, because
it may be expelled from the drive energetically.
it may be expelled from the drive energetically.
Connecting an Uninterruptible Power
Supply
Supply
1
Connect the uninterruptible power source to the
power outlet.
power outlet.
2
Connect the NSR to the UPS with the supplied
power cord.
power cord.
3
Connect the NSR to the UPS with the dedicated serial
cable to the serial connector on the rear of the NSR.
cable to the serial connector on the rear of the NSR.
Connecting Remote Client
If a remote client is required, the supplied RealShot
Manager Controller software can be used.
RealShot Manager Controller runs on Windows
computers. For details on system requirements, refer to
the release notes accompanying the RealShot Manager
Controller install archive. Also, make sure to use the
RealShot Manager supplied with the NSR.
Manager Controller software can be used.
RealShot Manager Controller runs on Windows
computers. For details on system requirements, refer to
the release notes accompanying the RealShot Manager
Controller install archive. Also, make sure to use the
RealShot Manager supplied with the NSR.
1
Use a network cable to connect LAN connector to
a network switch.
When using the NSR-100/50, connect to LAN
connector 2 on the unit.
a network switch.
When using the NSR-100/50, connect to LAN
connector 2 on the unit.
2
Connect the network cable to a computer when
RealShot Manager Controller software is installed.
RealShot Manager Controller software is installed.
Notes
• For details on installation and other topics related to
the RealShot Manager Controller software, refer to the
supplied NSR Series Manual, Tool & Source Codes
CD.
supplied NSR Series Manual, Tool & Source Codes
CD.
• When using RealShot Manager as a remote controller
for the NSR, select [Controller] during installation of
RealShot Manager.
RealShot Manager.
• The default connection port for the RealShot Manager
server function on the NSR unit is “8081”. The
connection port can be changed from the NSR.
connection port can be changed from the NSR.
• When using the NSR-100/50, use LAN connector 2 at
the rear of the NSR even if connecting it to the user
area of a network.
area of a network.
Network Camera
Network switch
POWER
1
2
3
LAN
1
2
3
4
HDD
1
2
3
4
ERROR
STATUS
REC
Windows PC
Network switch
RealShot Manager
Controller software
Controller software
(For the NSR-100/50)