ATTO Technology 2700C Benutzerhandbuch
53
ATTO Technology Inc. iPBridge Installation and Operation Manual
6.1.9 Mapping commands
You may map devices via the web-based server or through the management or serial ports.
Note
The recommended management tool for the
iPBridge is ATTO ExpressNAV.
iPBridge is ATTO ExpressNAV.
AccessControl
Controls access to a target node as keyed to the iSCSI
qualified name of whitelisted initiators.
Controls access to a target node as keyed to the iSCSI
qualified name of whitelisted initiators.
Note
AccessControl cannot be used with iSNS
Set syntax: set AccessControl [default | Target Name]
[enabled | disabled]
Get syntax: AccessControl [default | Target Name]
[enabled | disabled]
Get syntax: AccessControl [default | Target Name]
AccessEntry
Allows the addition or deletion of an initiator entry from
the access control list of a target node. The initiator name
must be an iSCSI qualified name and must be between 1
to 223 character. The name is case sensitive and cannot
be all.
Allows the addition or deletion of an initiator entry from
the access control list of a target node. The initiator name
must be an iSCSI qualified name and must be between 1
to 223 character. The name is case sensitive and cannot
be all.
Set syntax: set AccessEntry [default | Target Name]
[Initiator Name <delete> | all [delete]]
Get syntax: get AccessEntry [default | Target Name]
[Initiator Name <delete> | all [delete]]
Get syntax: get AccessEntry [default | Target Name]
AutoMap
Automatically assigns iSCSI LUNs to a set of Fibre
Channel target destination devices visible to the
iPBridge.Valid existing maps are not deleted. The
iPBridge reports a five-second delay while it scans for
devices.
Automatically assigns iSCSI LUNs to a set of Fibre
Channel target destination devices visible to the
iPBridge.Valid existing maps are not deleted. The
iPBridge reports a five-second delay while it scans for
devices.
Immediate command: AutoMap
FCHard
Used to enable or disable FC hard address assignment.
Under soft addressing, the FibreBridge loop address is
assigned during loop initialization. Use FCHardAddress
(described below) if you enable hard addressing.
Used to enable or disable FC hard address assignment.
Under soft addressing, the FibreBridge loop address is
assigned during loop initialization. Use FCHardAddress
(described below) if you enable hard addressing.
Default: disabled
Set syntax: set FCHard [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get FCHard
Set syntax: set FCHard [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get FCHard
FCHardAddress
Sets/displays the value used as the FC-AL hard address.
This hexadecimal value represents the address the
FibreBridge will try to use if hard addressing is enabled.
When an optional address is not present, the current value
is displayed. The valid range of values is 0 through 125.
Sets/displays the value used as the FC-AL hard address.
This hexadecimal value represents the address the
FibreBridge will try to use if hard addressing is enabled.
When an optional address is not present, the current value
is displayed. The valid range of values is 0 through 125.
Default: fp1= 0x03; fp2=0x04
Set syntax: set FCHardAddress [fp] [address]
Requires a SaveConfiguration command
Get syntax: get FCHardAddress [fp]
Set syntax: set FCHardAddress [fp] [address]
Requires a SaveConfiguration command
Get syntax: get FCHardAddress [fp]
FCTargets
Obtains information about every FC target device visible
to a FibreBridge operating in initiator mode; devices may
be used as targets for initiator mode features.
Obtains information about every FC target device visible
to a FibreBridge operating in initiator mode; devices may
be used as targets for initiator mode features.
Get syntax: FCTargets <fp>
iSCSITarget
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing. In verbose mode, overwriting a map
requires secondary confirmation of the action.
Creates/deletes an iSCSI target name. The target name
will act as a suffix to the standard bridge iSCSI-qualified
name. The target name may not exceed 24 characters. A
newly-created target has one LUN, the iPBridge LUN, at
LUN 0. If the target name already exists, this command
does nothing. In verbose mode, overwriting a map
requires secondary confirmation of the action.
Immediate command: iSCSITarget [Target Name]
<delete>
<delete>
iSCSITargetNameDisplay
Displays the iSCSI target name.
Displays the iSCSI target name.
Immediate command: iSCSITargetNameDisplay