Honeywell HE360 Installationsanleitung
HE360 HUMIDIFIER INSTALLATION KIT
3
69-1572
4.
Tape the template in position and trace around the
template.
template.
5.
Remove the template and carefully cut the rectan-
gular opening.
gular opening.
6.
Disassemble the humidifier; remove the cover and
take out the humidifier pad assembly. See Fig. 3.
take out the humidifier pad assembly. See Fig. 3.
Fig. 3. Disassembling humidifier.
7.
Make sure the humidifier housing is level, then
position it in the opening so the plastic tabs are in
place on the
position it in the opening so the plastic tabs are in
place on the
lower sheet metal edge
of the open-
ing. Use pliers, as necessary, to flatten cut edges.
See Fig. 4.
See Fig. 4.
8.
Secure the humidifier housing to the opening at the
top and bottom using sheet metal screws.
top and bottom using sheet metal screws.
Fig. 4. Installing humidifier on duct.
9.
Reinstall the humidifier pad assembly in the humid-
ifier housing.
ifier housing.
IMPORTANT
Be sure to reconnect the water feed tube and
ensure that the tube is not pinched or kinked.
ensure that the tube is not pinched or kinked.
10.
Hinge the cover in place and secure with the
thumbscrew located at the bottom of the cover.
thumbscrew located at the bottom of the cover.
CONNECTING PLUMBING
Use hot or cold water and either hard or softened water
in the humidifier.
in the humidifier.
1.
Shut off the water.
CAUTION
Chemical Hazard.
Can cause personal injury or equipment
damage.
Do not use any line connected to an air
conditioner.
Do not use gas line.
Can cause personal injury or equipment
damage.
Do not use any line connected to an air
conditioner.
Do not use gas line.
2.
Use the self-piercing saddle valve (included) to tap
into the water supply line at the location selected.
See Fig. 5. If tapping into galvanized pipe, drain
line and pre-drill 3/17 in. tap for saddle valve.
into the water supply line at the location selected.
See Fig. 5. If tapping into galvanized pipe, drain
line and pre-drill 3/17 in. tap for saddle valve.
NOTE:
The saddle valve is not designed to regulate
water flow. The valve is either open or closed.
water flow. The valve is either open or closed.
IMPORTANT
To prevent debris from clogging the solenoid in-
line filter, be sure to install the saddle valve han-
dle pointing toward the ceiling.
line filter, be sure to install the saddle valve han-
dle pointing toward the ceiling.
Fig. 5. Installing saddle valve.
3.
Use 1/4 in. (6 mm) OD tubing and connect the sad-
dle valve to the inlet side of the solenoid valve (see
Fig. 6).
a. Place the brass compression nut over the
dle valve to the inlet side of the solenoid valve (see
Fig. 6).
a. Place the brass compression nut over the
tubing.
b. Install brass insert into end of tubing.
c. Slide the plastic compression ring over the
c. Slide the plastic compression ring over the
tubing. (Discard copper compression ring pro-
vided with valve.)
vided with valve.)
NOTE:
To prevent leaking, use plastic (Delrin) sleeve
rings with plastic tubing. Use copper sleeve
rings only with copper tubing.
rings with plastic tubing. Use copper sleeve
rings only with copper tubing.
M12809
COVER
ASSEMBLY
ASSEMBLY
HUMIDIFIER
PAD ASSEMBLY
PAD ASSEMBLY
FEED TUBE NOZZLE
WATER
DISTRIBUTION TRAY
DISTRIBUTION TRAY
HUMIDIFIER
HOUSING
HOUSING
THUMB
SCREW
SCREW
DUCT
LEVEL
SHEET METAL
SCREWS (4)
SCREWS (4)
PLASTIC
TABS (2)
TABS (2)
DRAIN TUBING
M20204
OPENING
TO AIR DUCT
M20175
SCREW DRIVER
WATER LINE