Trane Gas Unit Heaters Wartungshandbuch
GKND-SVX01B-EN
7
General Information
Description
The Separated Combustion Gas Blower Unit Heater is a
factory assembled, power vented, high static pressure
type centrifugal blower unit designed for heavy duty
applications, such as continuous operation, or where a
single unit heater must do the entire heating job in a large
area. Blower type unit heaters may be used with the
factory assembled, power vented, high static pressure
type centrifugal blower unit designed for heavy duty
applications, such as continuous operation, or where a
single unit heater must do the entire heating job in a large
area. Blower type unit heaters may be used with the
standard adjustable louvers, or with short duct runs and
discharge nozzles for spot heating. Blower type unit
heaters may be used where low sound levels are required.
The designs are certified by ETL as providing a minimum
of 80 percent thermal efficiency, and approved for use in
California. Do not alter these units in any way. If you
have any questions after reading this manual, contact the
manufacturer.
discharge nozzles for spot heating. Blower type unit
heaters may be used where low sound levels are required.
The designs are certified by ETL as providing a minimum
of 80 percent thermal efficiency, and approved for use in
California. Do not alter these units in any way. If you
have any questions after reading this manual, contact the
manufacturer.
General Safety Information
Important:
This product must be installed by a licensed
plumber or gas fitter when installed within
the Commonwealth of Massachusetts.
plumber or gas fitter when installed within
the Commonwealth of Massachusetts.
•
Installation must be made in accordance with
local codes, or in absence of local codes with the
latest edition of ANSI Standard Z223.1 (N.F.P.A.
No. 54) National Fuel Gas Code.
local codes, or in absence of local codes with the
latest edition of ANSI Standard Z223.1 (N.F.P.A.
No. 54) National Fuel Gas Code.
All of the ANSI and NFPA Standards referred to
in these installation instructions are those that
were applicable at the time the design of this
appliance was certified. The ANSI Standards are
available from the American National Standards
Institute, INC.,11 West 42nd Street, New York,
NY., 10036 or www.ansi.org. The NFPA
Standards are available from the National Fire
Protection Association, Batterymarch Park,
in these installation instructions are those that
were applicable at the time the design of this
appliance was certified. The ANSI Standards are
available from the American National Standards
Institute, INC.,11 West 42nd Street, New York,
NY., 10036 or www.ansi.org. The NFPA
Standards are available from the National Fire
Protection Association, Batterymarch Park,
Quincy, MA 02269. These unit heaters are
designed for use in airplane hangars when
installed in accordance with current ANSI/NFPA
No. 409 and in public garages when installed in
accordance with current NFPA No. 88A and
NFPA No. 88B.
designed for use in airplane hangars when
installed in accordance with current ANSI/NFPA
No. 409 and in public garages when installed in
accordance with current NFPA No. 88A and
NFPA No. 88B.
If installed in Canada, the installation must
conform with local building codes, or in absence
of local building codes, with CAN/CanGa-B149.1
“Installation Codes for Natural Gas Burning
Appliances and Equipment” or CANCSA B149.2
“Installation Codes for Propane Gas Burning
Appliances and Equipment”
conform with local building codes, or in absence
of local building codes, with CAN/CanGa-B149.1
“Installation Codes for Natural Gas Burning
Appliances and Equipment” or CANCSA B149.2
“Installation Codes for Propane Gas Burning
Appliances and Equipment”
. These unit heaters
have been designed and certified to comply with
CSA 2.6. Also see sections on installation in
CSA 2.6. Also see sections on installation in
•
Do not alter the unit heater in any way or damage
to the unit and/or severe personal injury or death
could occur!
to the unit and/or severe personal injury or death
could occur!
•
Turn off the gas supply and disconnect all
electric power, including remote disconnects
before servicing unit. Follow proper lockout/
tagout procedures to ensure the power can not
be inadvertently energized and the gas can not
electric power, including remote disconnects
before servicing unit. Follow proper lockout/
tagout procedures to ensure the power can not
be inadvertently energized and the gas can not
Figure 1.
Power Vented Separated Combustion Blower Unit Heaters
Front view
Rear view
See
for unit components.
WARNING
Safety Alert!
You MUST follow all recommendations below. Failure
to do so could result in death or serious injury.
to do so could result in death or serious injury.