Hunter Fan 28984 Leaflet
41490-01 12/01/2005
3. Insert the chain and fan pull chain switch through
the round opening on the side of the modular
accessory light kit. Thread the bellmouth nut over
the pull chain and hand tighten the bellmouth
nut.
accessory light kit. Thread the bellmouth nut over
the pull chain and hand tighten the bellmouth
nut.
4. Reattach the patented breakaway connector to
the end of the pull chain.
5. Insert the reversing switch into the square hole
on the side of the modular accessory light kit.
Install and tighten the two screws you removed
in Step 1, substep 1.
Install and tighten the two screws you removed
in Step 1, substep 1.
6. Carefully place the capacitors in the modular ac-
cessory light kit.
You have completed the assembly of the modular
accessory light kit and are ready for installing the
modular accessory light kit to the fan.
accessory light kit and are ready for installing the
modular accessory light kit to the fan.
STEP 3: INSTALLING THE ACCESSORY
LIGHT KIT
LIGHT KIT
NOTE: Refer to Figure 3 for the steps listed below.
1. Connect the lower (mutli-wire) plug connector
1. Connect the lower (mutli-wire) plug connector
from the modular accessory light kit to the up-
per plug connector from the motor.
NOTE: Both plug connectors are polarized and will
only fit together one way. Make sure that both
connectors are properly aligned before connect-
ing them together. Incorrect connection could
cause improper operation and damage to the
product.
per plug connector from the motor.
NOTE: Both plug connectors are polarized and will
only fit together one way. Make sure that both
connectors are properly aligned before connect-
ing them together. Incorrect connection could
cause improper operation and damage to the
product.
2. Place the modular accessory light kit over the up-
per switch housing. Align the side screw holes in
the upper switch housing and the modular acces-
sory light kit. Attach the modular accessory light
kit to the upper switch housing with the three
#6-32 X 3/8" housing assembly screws.
the upper switch housing and the modular acces-
sory light kit. Attach the modular accessory light
kit to the upper switch housing with the three
#6-32 X 3/8" housing assembly screws.
STEP 4: INSTALLING THE BULBS AND
GLOBES
GLOBES
NOTE: Refer to Figure 4 for the steps listed below.
1. Insert a globe into the cup.
2. Tighten the thumbscrews manually. Do Not
1. Insert a globe into the cup.
2. Tighten the thumbscrews manually. Do Not
overtighten.
3. Repeat substeps 1 and 2 for the remaining three
globes.
4. Install a 60W medium base incandescent bulb into
each socket.
You have completed the installation of the modular
accessory light kit. Refer back to the “ Operating
Your Hunter Fan” section in the Installation/Owner’s
Manual provided with your Hunter fan for proper
operation instructions.
accessory light kit. Refer back to the “ Operating
Your Hunter Fan” section in the Installation/Owner’s
Manual provided with your Hunter fan for proper
operation instructions.
CUP
THUM B-
SCREW S
SCREW S
GLOBE
FIGURE 4
Hunter Fan Company
2500 Frisco Avenue
Memphis, TN 38114
USA
2500 Frisco Avenue
Memphis, TN 38114
USA
© 2005 Hunter Fan Co.
FIGURE 2
Fan Speed
Switch
Switch
Capacitor
Reverse Switch
M ulti-wire Plug
Connection
Connection
Capacitor
Bellmouth Nut
#6-62 Housing
A ssembly Screws
A ssembly Screws
Bellmouth Nut
Light Switch
W ires to Light Sockets
CAUTION
Be sure no bare wire or wire strands are visible after
making connections.
making connections.
UPPER SW ITCH
HOUSING
HOUSING
UPPER PLUG
CONNECTOR
CONNECTOR
HOUSING A SSEM BLY
SCREW
SCREW
FIGURE 3
LOW ER PLUG
CONNECTOR
CONNECTOR
LIGHT K IT