Vermont Casting 36XDV User Manual
XDV Direct Vent Gas Fireplace
24
10009383
Glass Information
Only glass approved by CFM Corporation
should be used on this fireplace.
should be used on this fireplace.
•
The use of any non-approved replacement glass will
void all product warranties.
void all product warranties.
•
Care must be taken to avoid breakage of the glass.
•
Do not operate appliance with glass front
removed, cracked or broken.
removed, cracked or broken.
•
Replacement glass (complete with gasket and
window frame) is available through your CFM
Corporation dealer and should only be installed
by a licensed qualified service person.
window frame) is available through your CFM
Corporation dealer and should only be installed
by a licensed qualified service person.
Louvre Removal
To remove louvre
assembly top, pull
louvre up and then
lift out. The louvre
assembly bottom is
hinged at the bottom
edge and swings
down. (Fig. 47)
assembly top, pull
louvre up and then
lift out. The louvre
assembly bottom is
hinged at the bottom
edge and swings
down. (Fig. 47)
Window Frame
Operating Instructions
Window Frame Assembly Removal
1. Turn the fireplace OFF (including the pilot).
2. If the unit has been operating, allow time for the
2. If the unit has been operating, allow time for the
components to cool.
3. Remove louvre assembly top.
4. Open the louvre assembly bottom.
5. Release the two clamps along lower edge of the
4. Open the louvre assembly bottom.
5. Release the two clamps along lower edge of the
frame by pulling down on clamp handles. (Fig. 48)
6. Tilt window frame assembly out slightly at the bot-
tom, lift the frame up and away from the fireplace.
7. To replace window frame assembly reverse proce-
dure.
1.
2.
FP444
remove louvre
12/99
remove louvre
12/99
Glass Panel
Louvre
FP444
Fig. 47 Remove louvre assembly
top.
top.
FP771a
DV360/580
GLASS REMOVAL-CLIP
1/27/00 djt
DV360/580
GLASS REMOVAL-CLIP
1/27/00 djt
Clamps
Window Frame
Assembly
Assembly
Fireplace
Front
Front
Glass
Panel
Panel
Glass
Panel
Panel
Pull
Clamp Hook
Fig. 48 Window frame assembly removal.
G584-501
Push
Clamp Handle
two or three times with a non-ammonia household
cleaner and warm water (gas fireplace glass cleaner
is recommended). After the initial cleaning process the
glass should be cleaned two or three times during each
operating season depending on the environment in the
house.
cleaner and warm water (gas fireplace glass cleaner
is recommended). After the initial cleaning process the
glass should be cleaned two or three times during each
operating season depending on the environment in the
house.
Clean the glass after the first two weeks of
operation.
Do not clean glass when hot.
Do not use abrasive cleaners.
Do not strike or slam the glass.
operation.
Do not clean glass when hot.
Do not use abrasive cleaners.
Do not strike or slam the glass.
Replacement Of
Ceramic Hearth Panels
1. Remove glass.
2. Set left and right panels on hearth and bring towards
2. Set left and right panels on hearth and bring towards
front of unit. (Fig. 49)
������
�������������������
����
�������������������
����
Ceramic
Hearth
Panel
Front of Unit
Fig. 49 Ceramic hearth panel location.
Grate
FP1611
Ceramic
Hearth Panel
Ember
Material
Main Burner Assembly
Front Burner
Glass Cleaning
It is necessary to clean the glass periodically. During
start-up condensation, which is normal, forms on the
inside of the glass and causes lint, dust and other
airborne particles to cling to the glass surface. Also
initial paint curing may deposit a slight film on the glass.
It is therefore recommended the glass be cleaned
start-up condensation, which is normal, forms on the
inside of the glass and causes lint, dust and other
airborne particles to cling to the glass surface. Also
initial paint curing may deposit a slight film on the glass.
It is therefore recommended the glass be cleaned