Dansons Group FPP Freestanding User Manual
Can
adian Comfort Industries V04
6
PELPRO OWNERS MANUAL
Copyright 2004
www.pelprostoves.com
Dansons Group Inc.
S
PECIFICATIONS
HEATING SPECIFICATIONS
Approx. Heating capacity (sq. feet) *
800 – 2,000
Approx. Fuel burn rate per hour **
1.5 – 5 lbs
Hopper Capacity - Traditional Stove / Insert
40 lbs
Approx. Burn time at lowest setting
27 hrs
Hopper Capacity – Bay View Free Standing
60 lbs
Approx. Burn time at lowest setting
48 hrs
Hopper Capacity – Bay View Insert / Built-In
40-60 lbs
Approx. Burn time at lowest setting
27-48
* Heating capacity will vary depending on floor plan layout of your home, degree of insulation, and the outside
temperature. Fuel size, quality, density and moisture level will also have an effect.
** Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use
temperature. Fuel size, quality, density and moisture level will also have an effect.
** Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use
PFI listed fuel for best results.
DIMENSIONS
ELECTRICAL SPECIFICATIONS
Electrical Rating
= 110-120 Volts 60 HZ 2.0 Amps
Watts (operational)
= 175 (approximately)
Watts (optional igniter)
= 475 (approximately)
A voltage surge protector or ground fault outlet is required for this unit.
EPA COMPLIANCE
This heater is exempt from EPA Phase II requirements, but has been tested for emissions using EPA test methods
by Warnock Hersey , US.
by Warnock Hersey , US.
FUEL CONSIDERATIONS
Your Pelpro pellet appliance, is designed to burn pellets that comply with Association of Pellet Fuel Industries
standards. (Minimum of 40lbs density per cubic ft, ¼ to 5/16’ diameter length no greater than 1.5”, not less than
8,200 BTU’s/lb, moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million)
Pellets that are soft, contain excessive amounts of loose sawdust, have been or are wet, produce clinkers and/or
heavy ash will result in reduced performance and may actually cause the fire to go out.
standards. (Minimum of 40lbs density per cubic ft, ¼ to 5/16’ diameter length no greater than 1.5”, not less than
8,200 BTU’s/lb, moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million)
Pellets that are soft, contain excessive amounts of loose sawdust, have been or are wet, produce clinkers and/or
heavy ash will result in reduced performance and may actually cause the fire to go out.
24”
28 3/4”
24”
18 3/4”
+
+
Shroud 1”
+
+
24”
6 1/2”
7 3/4”
8 1/4”
3 ½”
Exhaust
Air Inlet
8 1/4”
Air Inlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4”
24”
24 3/4”
12 1/4”
10 3/4”
+
+
24”
8 1/4”
Air Inlet
17 1/4”
12 3/4”
6 1/2”
Exhaust
24 3/4”
30”
24”
+
Shroud 1”
8 1/4”
Air Inlet
17”
12 3/4”
Exhaust
26”
12 1/4”
10 3/4”
+
25”
Air Inlet
7”
Exhaust
+
+
Exhaust
26”
+
24”
6 ½”
Exhaust
+
Air Inlet
8 1/4”
7 3/4”
3 ½”
24”
Bay View Freestanding
Bay View Insert / Built-In
Traditional Freestanding
Traditional Insert / Built-In
19”
-
23”
23”
Ad justable
Hopper
Hopper