GE ASQ28 User Manual
In the case of a power outage or interruption, the
unit will automatically re-start in the settings last
used after the power is restored. The Timer and
used after the power is restored. The Timer and
Sleep features will reset to the original setting.
You may need to set a new time if desired.
You may need to set a new time if desired.
Power Outage Recovery Feature
The vent control is located on the inside of the air
louvers in the lower right corner.
louvers in the lower right corner.
When set at CLOSE, only the air inside the room
will be circulated and conditioned. When set at
OPEN, some inside air is exhausted outside.
will be circulated and conditioned. When set at
OPEN, some inside air is exhausted outside.
Consumer Support
Tr
oubleshooting T
ips
Operating Instructions
Safety Instructions
Installation Instructions
ge.com
When the air conditioner is turned on, it will
automatically start in the setting last used.
automatically start in the setting last used.
Vent Control
To open the vent, push the lever to the
right. To close it, push it to the left.
right. To close it, push it to the left.
Cool Mode
Use the Cool mode with High (3), Med (2) or
Low (1) fan for cooling. Use the Increase ▲ /
Decrease ▼ pads to set the desired temperature
between 64°F and 86°F in 1°F increments.
Low (1) fan for cooling. Use the Increase ▲ /
Decrease ▼ pads to set the desired temperature
between 64°F and 86°F in 1°F increments.
A thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air
will become cooler. Set the thermostat at a higher
number and the indoor air will become warmer.
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air
will become cooler. Set the thermostat at a higher
number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned
on while set to Cool, it will take approximately 3 minutes
for the compressor to start and cooling to begin.
on while set to Cool, it will take approximately 3 minutes
for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode
and High (3) or Med (2) fan with a middle set
temperature.
and High (3) or Med (2) fan with a middle set
temperature.
For Maximum Cooling—Select the Cool mode
and High (3) fan with a lower set temperature.
and High (3) fan with a lower set temperature.
For Quieter & Nighttime Cooling—Select the
Cool mode and Low (1) fan with a middle set
temperature.
Cool mode and Low (1) fan with a middle set
temperature.
NOTE: If you switch from a Cool setting to Off or to
a fan setting, wait at least 3 minutes before switching
back to a Cool setting.
a fan setting, wait at least 3 minutes before switching
back to a Cool setting.
Air Direction—Up and Down
Fingertip pressure on the horizontal louvers adjusts
the air direction up or down.
the air direction up or down.
Fan Mode
Use the Fan at High (3), Med (2) or Low (1) to provide
air circulation and filtering without cooling.
air circulation and filtering without cooling.
Since fan only settings do not provide cooling,
a temperature setting will not be displayed.
a temperature setting will not be displayed.
Air Direction—Side-to-Side
The side-to-side air direction is adjusted
by the louver levers or by grasping and moving
the inner vertical louvers.
by the louver levers or by grasping and moving
the inner vertical louvers.
5
Additional controls and important information.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for
This cool-only air conditioner was not designed for
freezing outdoor conditions. It must not be used in
freezing outdoor conditions.
freezing outdoor conditions.