Lucent Technologies Release 7 User Manual
DEFINITY Enterprise Communications Server Release 7
Maintenance for R7r
Maintenance for R7r
555-230-126
Issue 4
June 1999
Additional Maintenance Procedures
6-49
Automatic Transmission Measurement System (ATMS)
6
ATMS Detail Report
This report is divided into two sections. The upper section lists the trunk group,
trunk type, trunk vendor, TTL type, and the user-defined threshold values
administered on page 4 of the trunk group form. The lower section lists the most
recent set of measurements for each member of the trunk group selected for the
report. Measurements that exceed the marginal threshold, but not the
unacceptable threshold, are highlighted. Measurements that exceed the
unacceptable threshold blink, identifying unusable trunks. When a marginal or
unacceptable measurement is located, scan the top section to find out how far
the measurement deviates from its defined threshold.
trunk type, trunk vendor, TTL type, and the user-defined threshold values
administered on page 4 of the trunk group form. The lower section lists the most
recent set of measurements for each member of the trunk group selected for the
report. Measurements that exceed the marginal threshold, but not the
unacceptable threshold, are highlighted. Measurements that exceed the
unacceptable threshold blink, identifying unusable trunks. When a marginal or
unacceptable measurement is located, scan the top section to find out how far
the measurement deviates from its defined threshold.
Output Fields - ATMS Detail Report
Measurements are made in both directions, near to far end, and far to near end.
For each measurement, there are 2 columns on the lower part of the report, “NE”
for near end, and “FE” for far end. These refer to the destination end for that
measurement.
For each measurement, there are 2 columns on the lower part of the report, “NE”
for near end, and “FE” for far end. These refer to the destination end for that
measurement.
Busied Out Trunks
The number of trunks that were busied out in response to test
failures. These may be caused by hardware problems, incorrect
threshold values, and so on.
failures. These may be caused by hardware problems, incorrect
threshold values, and so on.
Group
The trunk group number selected.
Type
The trunk group type.
Vendor
The vendor of this trunk group.
ATMS TRUNK MEASUREMENTS
Group: 78 Type: co Vendor: AT&T TTL Type: 105-w-rl
THRESHOLD VALUES
Loss dev at
1004Hz-loss 404Hz 2804Hz C-msg C-ntch SRL SRL
Min Max - + - + Noise Noise LO HI ERL
Marginal -2 21 9 9 9 9 55 74 0 0 0
Unacceptable -2 21 9 9 9 9 55 74 0 0 0
Trk Test Test Test -16dBm OdBm
Mem Date Time Rslt FE NE FE NE FE NE FE NE FE NE FE NE FE NE FE NE FE NE
1 10/04 14:25 pass 7 7 7 7 -2 -2 7 7 15 28 34 34 8 16 11 16 11 17
2 10/04 14:26 1920
3 10/04 14:27 1000
4 10/04 14:28 pass 7 7 7 7 -2 -2 7 7 15 29 38 34 8 16 11 15 11 16
5 10/04 14:29 pass 7 7 7 7 -2 -2 6 6 15 35 34 34 8 6 9 6 10 7
6 10/04 14:30 pass 7 7 7 7 -2 -2 6 6 15 26 34 34 8 16 9 13 10 16
7 10/04 14:31 pass 7 7 7 7 -2 -2 7 7 15 30 34 34 8 16 9 11 10 13
8 10/04 14:32 pass 6 6 6 6 -2 -2 6 6 15 25 34 34 10 17 11 16 12 17
9 10/04 14:33 pass 6 6 7 7 -1 -1 7 7 15 25 34 34 8 15 9 13 10 16
10 10/04 14:34 pass 6 6 7 6 -1 -1 7 7 15 36 34 35 8 6 9 6 10 7