Campbell Hausfeld HL5404 User Manual
Warning indicates a
potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
avoided, COULD result in death or
serious injury.
Caution indicates a
potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
avoided, MAY result in minor or
moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
cause damage to equipment.
nOte: Information that requires special
attention.
attention.
General safety Information
CaLIFORnIa PROPOsItIOn 65
This product or
its power cord may
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
You can
create
dust when you cut, sand, drill
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
GeneRaL saFety
• Only persons well acquainted with
• Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit.
be allowed to use the unit.
Do not operate unit
if damaged during
shipping, handling or use. Damage may
result in bursting and cause injury or
property damage.
result in bursting and cause injury or
property damage.
Do not run
unattended. Leaving
compressor in AUTO position may allow
it to turn on inadvertently. To prevent
this and possible damage from power
surge, turn to OFF position after each
use.
it to turn on inadvertently. To prevent
this and possible damage from power
surge, turn to OFF position after each
use.
Since the air compressor and other
components (filters, lubricators, hoses,
etc.) used, make up a high pressure
pumping system, the following safety
components (filters, lubricators, hoses,
etc.) used, make up a high pressure
pumping system, the following safety
precautions must be observed at all
times:
1. Read all manuals included
times:
1. Read all manuals included
with this product carefully.
Be thoroughly familiar
with the controls and the
proper use of the equipment.
Be thoroughly familiar
with the controls and the
proper use of the equipment.
2. Follow all local electrical and
safety codes as well as in the US,
National Electrical Code (NEC) and
Occupational Safety and Health Act
(OSHA).
National Electrical Code (NEC) and
Occupational Safety and Health Act
(OSHA).
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.
be allowed to use the compressor.
4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the pump
or unit.
when operating the pump
or unit.
6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
Motors,
electrical
equipment and controls can
cause electrical arcs that
will ignite a flammable gas
or vapor. Never operate or repair in or
near a flammable gas or vapor. Never
store flammable liquids or gases in the
vicinity of the compressor.
cause electrical arcs that
will ignite a flammable gas
or vapor. Never operate or repair in or
near a flammable gas or vapor. Never
store flammable liquids or gases in the
vicinity of the compressor.
Compressor parts may be hot
even if the unit is stopped.
even if the unit is stopped.
9. Keep fingers away from
a running compressor; fast moving
and hot parts will cause injury and/
or burns.
and hot parts will cause injury and/
or burns.
10. If the equipment should start
to abnormally vibrate, STOP
the engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
the engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
2
Operating Instructions and Parts Manual
safety Guidelines
(Continued)
11. To reduce fire hazard, keep engine/
motor exterior free of oil, solvent, or
excessive grease.
excessive grease.
Never remove or
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
from paint and other accumulations.
Never
attempt
to repair or modify a tank!
Welding, drilling or any other
modification will weaken the
tank resulting in damage from rupture
or explosion. Always replace worn or
damaged tanks.
Welding, drilling or any other
modification will weaken the
tank resulting in damage from rupture
or explosion. Always replace worn or
damaged tanks.
Drain liquid from
tank daily.
13. Tanks rust from moisture build-up,
which weakens the tank. Make sure
to drain tank regularly and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
to drain tank regularly and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
14. Fast moving air will stir up dust
and debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.
Release air slowly when draining
moisture or depressurizing the
compressor system.
sPRayInG PReCaUtIOns
Do not
spray
flammable materials in
vicinity of open flame or near
ignition sources including the
compressor unit.
vicinity of open flame or near
ignition sources including the
compressor unit.
15. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
substances.
16. Use a face mask/
respirator when spraying
and spray in a well
ventilated area to prevent
health and fire hazards.
and spray in a well
ventilated area to prevent
health and fire hazards.
17. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
18. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
the instructions provided by the
chemical manufacturer.
MANUAL