SMSC LAN9312 User Manual
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Revision 1.4 (08-19-08)
264
SMSC LAN9312
DATASHEET
8:7
RESERVED
RO
-
6
PME Buffer Type (PME_TYPE)
When this bit is cleared, the PME pin functions as an open-drain buffer for
use in a wired-or configuration. When set, the PME pin is a push-pull driver.
When this bit is cleared, the PME pin functions as an open-drain buffer for
use in a wired-or configuration. When set, the PME pin is a push-pull driver.
Note:
When PME is configured as an open-drain output, the PME_POL
field of this register is ignored and the output is always active low.
field of this register is ignored and the output is always active low.
0: PME pin open-drain output
1: PME pin push-pull driver
1: PME pin push-pull driver
R/W
NASR
0b
5
Wake On LAN Status (WOL_STS)
This bit indicates that a wake-up frame or magic packet was detected by the
Host MAC.
This bit indicates that a wake-up frame or magic packet was detected by the
Host MAC.
In order to clear this bit, it is required that the event in the Host MAC be
cleared as well. The event sources are described in
cleared as well. The event sources are described in
.
R/WC
0b
4
RESERVED
RO
-
3
PME Indication (PME_IND)
The PME signal can be configured as a pulsed output or a static signal,
which is asserted upon detection of a wake-up event. When set, the PME
signal will pulse active for 50mS upon detection of a wake-up event. When
cleared, the PME signal is driven continuously upon detection of a wake-up
event.
The PME signal can be configured as a pulsed output or a static signal,
which is asserted upon detection of a wake-up event. When set, the PME
signal will pulse active for 50mS upon detection of a wake-up event. When
cleared, the PME signal is driven continuously upon detection of a wake-up
event.
0: PME 50mS pulse on detection of event
1: PME driven continuously on detection of event
1: PME driven continuously on detection of event
The PME signal can be deactivated by clearing the WOL_STS bit or by
clearing the appropriate enable.
clearing the appropriate enable.
R/W
0b
2
PME Polarity (PME_POL)
This bit controls the polarity of the PME signal. When set, the PME output
is an active high signal. When cleared, it is active low.
This bit controls the polarity of the PME signal. When set, the PME output
is an active high signal. When cleared, it is active low.
Note:
When PME is configured as an open-drain output, this field is
ignored and the output is always active low.
ignored and the output is always active low.
0: PME active low
1: PME active high
1: PME active high
R/W
NASR
0b
1
PME Enable (PME_EN)
When set, this bit enables the external PME signal pin. When cleared, the
external PME signal is disabled.
When set, this bit enables the external PME signal pin. When cleared, the
external PME signal is disabled.
Note:
This bit does not affect the PME_INT interrupt bit of the
.
0: PME pin disabled
1: PME pin enabled
1: PME pin enabled
R/W
0b
0
Device Ready (READY)
When set, this bit indicates that the LAN9312 is ready to be accessed. Upon
power-up, nRST reset, soft reset, or digital reset, the host processor may
interrogate this field as an indication that the LAN9312 has stabilized and is
fully active.
When set, this bit indicates that the LAN9312 is ready to be accessed. Upon
power-up, nRST reset, soft reset, or digital reset, the host processor may
interrogate this field as an indication that the LAN9312 has stabilized and is
fully active.
This bit can cause an interrupt if enabled.
Note:
With the exception of the HW_CFG, PMT_CTRL, BYTE_TEST, and
RESET_CTL registers, read access to any internal resources is
forbidden while the READY bit is cleared. Writes to any address
are invalid until this bit is set.
RESET_CTL registers, read access to any internal resources is
forbidden while the READY bit is cleared. Writes to any address
are invalid until this bit is set.
Note:
This bit is identical to bit 27 of the
.
RO
0b
BITS
DESCRIPTION
TYPE
DEFAULT