Liebherr 200514 User Manual

(2) Fan button

(7) SuperFrost buttont

(3) Setting button, refriger-

ator compartment

(8) Alarm button

(4) Refrigerator compart-

ment temperature

display

(9) On/Off button, freezer

compartment

(5) Freezer compartment

temperature display

The following are displayed in normal operation:

-

the set freezing temperature

-

the set cooling temperature

The freezer compartment temperature display flashes:

-

the temperature setting is being changed

-

after switch-on the temperature is not yet cold enough

-

the temperature has risen several degrees

Risk  of  injury  and  danger  of  damage  as  a  result  of  incorrect

transport!

u

Transport the appliance in a packed condition.

u

Transport the appliance upright.

u

Do not transport the appliance without assistance.

Fire hazard due to dampness!

If  live  parts  or  the  mains  lead  become  damp  this  may  cause

short circuits.

u

The appliance is designed for use in enclosed areas. Do not

operate  the  appliance  outdoors  or  in  areas  where  it  is

exposed to splash water or damp conditions.

Risk of fire due to short circuit!

If  the  mains  cable/connector  of  the  appliance  or  of  another

appliance  touch  the  rear  of  the  appliance,  the  mains  cable/

connector  may  be  damaged  by  the  appliance  vibrations,

leading to a short circuit.

u

Stand the appliance so that it is not touched by connectors

or main cables.

u

Do not plug the appliance or any others into sockets located

near the rear of the appliance.

Fire hazard due to refrigerant!

The  refrigerant  R  600a  is  environmentally  friendly  but  flam-

mable. Escaping refrigerant may ignite.

u

Do not damage the piping of the refrigeration circuit.

Fire hazard and danger of damage!

u

Do  not  place  appliances  emitting  heat  e.g.  microwaves,

toasters etc. on the appliance!

Blocked ventilation openings pose a risk of fire and damage!

u

Always keep the ventilation openings clear. Always ensure

that the appliance is properly ventilated!

Risk of damage due to condensate!

u

Do  not  install  the  appliance  directly  alongside  a  further

refrigerator/freezer.

q

In  the  event  that  the  appliance  is  damaged,  contact  the

supplier immediately before connecting to the mains.

q

The floor at the site must be flat and level.

q

Do not install the appliance in a location where it is exposed

to  direct  radiation  of  the  sun,  next  to  a  cooker,  heater  and

similar.

q

Always stand the appliance backed directly to the wall using

the enclosed wall spacers (see below).

q

The appliance may be moved only when it is empty.

q

Do not install the appliance without assistance.

q

The  more  R  600a  refrigerant  there  is  in  the  appliance,  the

larger the room in which the appliance is standing needs to

be. In rooms that are too small, a flammable mix of gas and

air  may  be  created  if  there  is  a  leak.  According  to  the  EN

378  standard,  every  11  g  of  R  600a  refrigerant  requires  at

least 1 m

3

 space in the room for the appliance. The amount

of refrigerant in your appliance is on the type plate inside the

appliance.

u

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

u

Remove  the  protective  film  from  the  outside  of  the  appli-

ance.*

The  stainless  steel  doors  are  finished  with  a  high  quality

surface coating and must not be treated with the enclosed care

product,

as otherwise the surface coating will be damaged.

u

Please only use a soft clean cloth to wipe the coated door

surfaces.

u

Only  use  a  stainless  steel  care  product  on  the  stainless

steel  side  walls,  applying  it  evenly  in  the  direction  of

polishing. Subsequent cleaning will then be easier.

u

Use  only  a  soft  clean  cloth  to  wipe  side  walls  and  door

surfaces with a paint finish.

u

Remove  the  protective  film  from  the  decorative  trims  and

drawer fronts.*

u

Remove all transit supports.

The  spacers  supplied  with  some  appliances  must  be  used  to

achieve the stated energy consumption. These will extend the

depth of the appliance by approx. 35 mm. The appliance is fully

functional if the spacers are not used, but does have a slightly

higher energy consumption.