Revel sub15 User Guide
Figure 13. How to connect the
ULTIMA SUB-15/LE-1
without a high-pass crossover.
ULTIMA SUB-15/LE-1
without a high-pass crossover.
CONNECTIONS (Continued)
SUB-15/LE-1 WITHOUT HIGH-PASS CROSSOVER
Revel recommends using both a low-pass and high-pass crossover
with any “main” left and right loudspeakers. The FM-2 module is
designed to be transparent when inserted in the main signal path.
The use of a high-pass crossover greatly reduces distortion, increases
dynamic range, and optimizes the transition from the ULTIMA
SUB-15 to the main loudspeakers. Your Revel dealer can help with
the proper FM-2 settings.
with any “main” left and right loudspeakers. The FM-2 module is
designed to be transparent when inserted in the main signal path.
The use of a high-pass crossover greatly reduces distortion, increases
dynamic range, and optimizes the transition from the ULTIMA
SUB-15 to the main loudspeakers. Your Revel dealer can help with
the proper FM-2 settings.
If the ULTIMA SUB-15/LE-1 will be used without a high-pass
crossover (see Figure 13), contact your Revel dealer for help in
setting the FM-2 low-pass crossover so the main speakers and the
ULTIMA SUB-15(s) will produce an optimum combined response.
crossover (see Figure 13), contact your Revel dealer for help in
setting the FM-2 low-pass crossover so the main speakers and the
ULTIMA SUB-15(s) will produce an optimum combined response.
ULTIMA SUB-15/LE-1
Owner’s Manual
22
Preamplifier
(rear)
Right Output
LeftOutput
Main Amplifier
(rear)
To Main Speakers
Left Input
Left
Right
Right Input
LE-1 Rear Panel
F
U S E
F
US
E
Caution: Connect to Revel Subwoofers only!
Floating Ground. Do not connect loudspeaker
outputs to any grounded equipment.
No user servicable parts inside.
For service contact Revel or an authorized dealer.
Refer to Owner's Manual for proper operating
instructions and safety precautions.
Floating Ground. Do not connect loudspeaker
outputs to any grounded equipment.
No user servicable parts inside.
For service contact Revel or an authorized dealer.
Refer to Owner's Manual for proper operating
instructions and safety precautions.
Serial No.
Freq Eq
In/Out
Music Sensor
Bypass -
Press & Hold
Five Seconds
In/Out
Music Sensor
Bypass -
Press & Hold
Five Seconds
Right Input
Right Output to main amplifier
Left Output to main amplifier Out to LE-1
Left Input
Inputs
Balanced
Balanced
Unbalanced
Sub # 1
Sub # 2
Revel
Northridge, CA/U.S.A.
Designed & Manufactured in U.S.A.
Northridge, CA/U.S.A.
Designed & Manufactured in U.S.A.
REVEL LE-1
LOW FREQUENCY
ELECTRONICS SYSTEM
LOW FREQUENCY
ELECTRONICS SYSTEM
Use T12A
250V Fuse
Only!
250V Fuse
Only!
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION:
RISK DE CHOC ELECTRIQUE
NE PAS OUVRIR
NRTL/C
UL-6500
120VAC ~ 60 Hz 720W
Power
Trigger
In
Crossover
Low Pass
Frequency (Hz)
Frequency (Hz)
High Pass
Frequency (Hz)
Frequency (Hz)
Revel FM-2
Filter Module
Filter Module
Enabled
Disabled
50
60
40
70
30
80
50
60
40
70
30
80
Chatsworth, California
Serial No.
SUB-15
ULTIMA
Made In U.S.A.
Connect to Revel
Ultima LE-1 Only!
Caution:
SUB-15 Rear Panel
or
or
Y adapter
Y adapter
NOTE: Enable Crossover
(i.e., switch is OUT). Adjust
Low Pass Frequency for optimum
blend with front speakers.
Crossover
Low Pass
Frequency (Hz)
Frequency (Hz)
Enabled
Disabled
50
60
40
70
30
80
NOTE: Use Y adapters or
Sub Outputs on Preamplifier
(if available) to drive LE-1.
Sub Outputs on Preamplifier
(if available) to drive LE-1.