Sony FA-HS1AM Manual

Page of 2
日本語
 
安全のために
ソニー製品は安全に充分配慮して設計されています。しかし、ま
ちがった使いかたをすると、火災などにより人身事故になること
があり危険です。事故を防ぐために次のことを必ずお守りくださ
い。
 
安全のための注意事項を守る
 
故障したら使わずに、ソニーの相談窓口に修理を依頼する
 
万一、異常が起きたら
警告表示の意味
取扱説明書では、次のような表示をしています。表示の内容
をよく理解してから本文をお読みください。
この表示の注意事項を守らないと、火災・感電
などにより死亡や大けがなど人身事故の原因
となります。
注意を促す記号
行為を禁止する記号
 
電源を切る
 
電池をはずす
 
ソニーの相談窓口に修理を依頼す
製品および同梱物を、幼児・子供の手の届く範囲に
放置しないでください。
幼児の手の届かない場所に置き、口に入れないよう注意
する。万一、飲み込んだ場合は、ただちに医師に相談し
てください。
落下や損傷により内部が露出した場合は、すみやか
に電池を抜き、使用を中止してください。
感電や火傷の恐れがあります。また内部に手を触れな
いでください。
万一、使用中に高熱、焦げ臭い、煙が出る等の異常を
感じたら、すみやかに電池を抜き、使用を中止してく
ださい。
電池についての安全上のご注意
漏液、発熱、発火、破裂などを避けるため、下記
のことを必ずお守りください。
取り扱い上のご注意
電池について
 
電池の製造後の経過期間により、新しい電池でも電池寿命が本
紙の記載と異なる場合があります。また、長期間の旅行や寒い
ところでは予備の電池をご用意ください。なお低温のために性
能が低下した電池でも、常温に戻せば、性能は回復します。
使用温度について
 
急激な温度変化を与えると内部に水滴を生じる可能性がありま
す。スキー場のような寒い屋外から暖かい室内に持ち込む場合
は、寒い屋外でビニール袋などに入れ、袋の中の空気を絞り出し
て密閉します。その後室内に持ち込み、周囲の温度に充分なじ
ませてから取り出してください。
その他のご注意
 
本機は防水構造になっていません。万一、水に濡れた場合は乾
いた布でふき取り、すみやかにソニーの相談窓口にご相談くだ
さい。
 
本機を絶対に分解しないでください。故障したときは、必ずソ
ニーの相談窓口にご相談ください。
 
本機のお手入れには、柔らかい布で汚れを軽くふき取ってくだ
さい。シンナー、ベンジンなどの有機溶剤を含むクリーナーは
絶対に使用しないでください。
 
直射日光下の車内など極度の高温下や、湿度の高いところに放
置しないでください。
 
感電の原因となることがありますので、ぬれた手でさわらない
でください。
互換性について
 
下記
URL
より、本機とデジタル一眼レフカメラの互換情報をご
覧いただけます。
 
http://www.sony.co.jp/alpha/support/
 
各部の名前
1 
ホットシュー(
ISO518
準拠)
2 
取りはずしボタン
3  BATTERY CHECK
ランプ
4  BATTERY CHECK
ボタン
5 
オートロックフット
6  POWER
スイッチ
電池の容量について
ご使用になる前に、本機の電池容量が充分かを以下の手順でご確
認ください。
1
  POWER
スイッチを
ON
の方向にスライドさせ電
源を入れる。
2
  BATTERY CHECK
ボタンを押す。
 
電池容量が充分な場合、
BATTERY CHECK
ボタンを押して
いる間は
BATTERY CHECK
ランプ(緑ランプ)が点灯します。
 BATTERY CHECK
ランプが点滅する場合は、電池容量が残
り少なくなっていますので、電池の交換をおすすめします。
点灯も点滅もしない場合は、電池を交換してください。
 
使用方法
カメラに本機を取り付けることにより、ワイヤレスフラッシュシ
ンクロシステムなどのホットシュー対応外部機器を以下の手順
でカメラに装着し、使用することができます。
1
 
カメラの電源を
OFF
にし、カメラのアクセサリー
シューのキャップをはずす。
2
 
本機の
POWER
スイッチを
OFF
にして、本機の
オートロックフットを、カメラ側のオートロック
アクセサリーシューに取り付ける。
 
カチッと音がするまでしっかり差し込みます。
 
本機をご使用になる前に、必ずカメラの内蔵フラッシュを
閉じてください。また、内蔵フラッシュの自動発光機能が
あるカメラでは、自動発光機能をオフにしておいてくださ
い。
下記の注意事項を守らないと、
 
火災・感電
により
死亡
大けが
の原因となります。
 
指定された電池以外は使わないでください。
 
電池の極性(+
/
−)を逆に入れないでください。
 
電池を火中へ投入したり、充電、ショート、分解、
加熱をしないでください。
 
電池は使い切ってから廃棄してください。また
廃棄するときは、テープなどで接点部を絶縁し
てください。
 
電池容量が残っていたり、他の金属と接触した
りすると、発熱・破裂・発火の恐れがあります。
 
お住いの自治体の規則にしたがって正しく廃棄
するかリサイクルしてください。
もし電池の液が漏れたときは、電池ケース内の漏れた液をよくふ
きとってから、新しい電池を入れてください。万一、液が身体や衣
服についたときは、水でよく洗い流してください。
変な音やにおい、
 
煙が出た場合は
電気製品は安全のための注意事項を守らない
と、火災や人身事故になることがあります。
この取扱説明書には、事故を防ぐための重要な注意事項と
製品の取り扱いかたを示しています。
この取扱説明書をよくお読みのうえ、製品を安全にお使い
ください。お読みになったあとは、いつでも見られるとこ
ろに必ず保管してください。
3
 
本機のホットシューに外部機器を矢印方向へスラ
イドさせ、しっかり差し込む。
ご注意
 
外部機器の使用方法については、外部機器の説明書をよく
お読みください。
 
外部機器によっては取り付けできない場合があります。ま
た、他社製フラッシュについては
フラッシュシステムに
適合しないため推奨しません。
4
 
本機の
POWER
スイッチを
ON
の方向にスライド
させ、電源を入れる。
 
本機の電池は、カメラのシャッターボタンを押すたびに消
耗します。
5
 
使用後は、本機の
POWER
スイッチを
OFF
にして
外部機器をはずし、本機の取りはずしボタンを押
しながら、本機を矢印方向にスライドさせて取り
はずす。
 
電池交換のしかた
ボタン型
3V
リチウム電池(ソニー製
CR1220
)の電池を使用しま
す。
1
 
電池室ふたを矢印の方向へスライドさせ、電池室
ふたを取りはずす。
 
本機の電源を
OFF
にした状態で電池を交換してください。
2
 
先が平らな絶縁物を図のようにすき間に差し込
む。
ご注意
 
すき間に差し込む際、つめなどで無理に押さないでくださ
い。けがをする場合があります。
 
すき間よりも幅の広いものを差し込まないでください。本
機が破損する恐れがあります。
 
差し込んだもので電池室内の端子部をこじないでください。
3
 
図のように軽く指を添えて電池が飛び出さないよ
うにしながら、先が平らな絶縁物で矢印の方向に
押し出して電池を取り出す。
 
電池が飛び出す場合がありますのでご注意ください。
4
 
+
”が手前に向くようにして、図のように電池を
電池ホルダーのフチに引っ掛けて電池を入れる。
5
 
電池室ふたを元どおりに入れ、カチッと音がする
までふたを閉じる。
主な仕様
シンクロ電圧
  60 V
以下、逆極性対応
電池
 
ボタン型
3V
リチウム電池(
CR1220
電池寿命
 
10,000 
回撮影
外形寸法
 
 35.5 
×
 24.4 
×
 54.8 mm
(幅/高さ/奥行き)
 
 
(突起部を除く)
質量
 
30 g
(電池含まず)
動作温度
 
C
40 
C
保存温度
 
-20 
C
+60 
C
内容物
 
ホットシューアダプター
 
FA-HS1AM
本機(
1
 
(ボタン型
3V
リチウム電池(
CR1220
)内蔵)
 
印刷物一式
仕様および外観は、改良のため予告なく変更することがあります
が、ご了承ください。
はソニー株式会社の商標です
保証書とアフターサービス
保証書
 
この製品には保証書が添付されていますので、お買い上げの際
お買い上げ店でお受け取りください。
 
所定事項の記入および記載内容をお確かめのうえ、大切に保存
してください。
 
保証期間は、お買い上げ日より
1
年間です。
アフターサービス
調子が悪いときはまずチェックを
この取扱説明書をもう一度ご覧になってお調べください。
それでも具合が悪いときは
ソニーの相談窓口にご相談ください。
保証期間中の修理は
保証書の記載内容に基づいて修理させていただきます。
詳しくは保証書をご覧ください。
保証期間経過後の修理は
修理によって機能が維持できる場合は、ご要望により有償修理さ
せていただきます。
部品の保有期間について
当社では本機の補修用性能部品(製品の機能を維持するために必
要な部品)を、製造打ち切り後最低
7
年間保有しています。この部
品保有期間を修理可能の期間とさせていただきます。保有期間が
経過したあとも、故障箇所によっては修理可能の場合があります
ので、ソニーの相談窓口にご相談ください。
ご相談になるときは、次のことをお知らせください。
 
品名:
FA-HS1AM
 
故障の状態:できるだけ詳しく
 
購入年月日
For the Customers in Europe
Disposal of Old Electrical & Electronic 
Equipment (Applicable in the 
European Union and other European 
countries with separate collection 
systems) 
This symbol on the product or on its 
packaging indicates that this product shall 
not be treated as household waste. Instead 
it shall be handed over to the applicable 
collection point for the recycling of 
electrical and electronic equipment. 
By ensuring this product is disposed of 
correctly, you will help prevent potential 
negative consequences for the environment 
and human health, which could otherwise 
be caused by inappropriate waste handling 
of this product. The recycling of materials 
will help to conserve natural resources. 
For more detailed information about 
recycling of this product, please contact 
your local Civic Office, your household 
waste disposal service or the shop where 
you purchased the product.
Disposal of waste batteries (applicable 
in the European Union and other 
European countries with separate 
collection systems)
This symbol on the battery or on the 
packaging indicates that the battery 
provided with this product shall not be 
treated as household waste.
By ensuring these batteries are disposed of 
correctly, you will help prevent potentially 
negative consequences for the environment 
and human health which could otherwise 
be caused by inappropriate waste handling 
of the battery. The recycling of the 
materials will help to conserve natural 
resources.
In case of products that for safety, 
performance or data integrity reasons 
require a permanent connection with an 
incorporated battery, this battery should 
be replaced by qualified service staff only.
To ensure that the battery will be treated 
properly, hand over the product at end-of-
life to the applicable collection point for 
the recycling of electrical and electronic 
equipment.
For all other batteries, please view the 
section on how to remove the battery from 
the product safely. Hand the battery over 
to the applicable collection point for the 
recycling of waste batteries.
For more detailed information about 
recycling of this product or battery, please 
contact your local Civic Office, your 
household waste disposal service or the 
shop where you purchased the product.
< Notice for the customers in the 
countries applying EU Directives >
The manufacturer of this product is Sony Corporation, 
1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The 
Authorized Representative for EMC and product safety is 
Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 
Stuttgart, Germany. For any service or guarantee matters 
please refer to the addresses given in separate service or 
guarantee documents.
Notes on use
A note about the battery 
  Depending on the time elapsed since manufacture 
of the batteries, their life may vary from the values 
described in this operating instructions, even if this unit 
is provided with new batteries. We recommend having 
spare batteries. It should be noted that battery capacity 
decreases as temperatures drop. Allow the battery 
to return to normal room temperature to restore the 
battery to its normal charge.
Operating temperature
  A rapid increase in temperature causes condensation 
to form inside this unit. If you need to bring this unit 
directly in from the cold to a warm environment, place 
the unit in a plastic bag while you are outdoors, and try 
to extract as much air as you can from inside the bag 
before sealing the bag. You can remove the unit from the 
bag when the air temperature around the bag has had a 
chance to gradually rise.
Other cautions
  This unit is not waterproof. If it comes in contact with 
water, wipe it dry with a clean cloth and take it to the 
nearest Sony dealer immediately.
  Never attempt to disassemble this unit. Take it to the 
nearest Sony dealer immediately for repair.
  When dirty, this unit may be cleaned with a clean, dry 
cloth. Do not allow this unit to come in contact with 
alcohol or other chemicals.
  Never leave this unit where it may be subjected to 
extreme temperatures, such as the glove compartment 
of a car, or to high humidity.
  Do not touch the unit with wet hands. This may cause 
electric shock.
Compatibility
  For details about this unit and digital single reflex 
camera compatibility, refer to the following URL. 
http://www.sony.net
 Identifying the parts
1  Hot shoe (ISO518-compatible)
2  Release button
3  BATTERY CHECK lamp
4  BATTERY CHECK button
5  Mounting foot
6  POWER switch
Battery capacity
Before using the battery, ensure that it has sufficient power 
for the following operations.
1
  Turn on the unit΄s power by sliding the 
POWER switch to ON.
2
  Hold down the BATTERY CHECK button.
 If the battery has a sufficient charge, the BATTERY 
CHECK lamp (green lamp) will light while pressing 
the BATTERY CHECK button.
 If the BATTERY CHECK lamp starts to blink, that 
means that the battery does not have a sufficient 
charge. It is recommended that you change the 
battery. If the BATTERY CHECK lamp does not 
light or blink, that means that the battery must be 
replaced.
 Using this unit
By attaching this unit to the camera, you can attach the 
external device compatible with hot shoe like a wireless 
flash sync system to the camera and use it with following 
steps.
1
  Turn off the power of the camera and slide 
the accessory shoe cap of the camera.
2
  Turn off the unit΄s power and slide the 
mounting foot into the auto-lock accessory 
shoe of the camera.
 Slide the mounting foot of this unit firmly until it 
clicks.
 Before using this unit, close the built-in camera flash. 
When using this unit with a camera that has an auto 
flash function, set the auto flash function to “OFF.”
3
  Slide the external device in the direction of 
the arrow to attach it firmly to the hot shoe 
of this unit.
Notes
 For details about handling the external device, refer 
to the external device operating instructions.
 Depending on the external device, you cannot 
attach it to this unit. Competitor flashes are not 
recommended because they are not compatible with 
the 
 flash system.
4
  Turn on the unit΄s power by sliding the 
POWER switch to ON.
 Battery power of this unit is depleted by pressing the 
shutter button of the camera.
5
  After use, turn off this unit’s power and 
remove the external device from this unit. 
Then remove this unit by sliding it in the 
direction of arrow as illustrated while 
pressing the release button.
 Changing the batteries
Use a button type 3V lithium battery (CR1220) with this 
unit.
1
  Slide the battery-chamber cover in the 
direction of arrow to remove the cover.
 Turn off the power of this unit when replacing the 
battery.
2
  Insert a flat-tipped insulator into the space 
between the battery and adaptor body as 
illustrated.
Notes
 Do not insert your fingernail because you can be 
injured.
 Do not insert an object that it is thicker than the 
space because you can damage the unit.
 Do not apply excessive force to the terminal in the 
battery-chamber by inserting anything.
3
  As illustrated, press the battery lightly with 
your finger not to pop out and press the 
battery with a flat-tipped insulator in the 
direction of the arrow to remove the battery.
 Be careful not to pop out the battery when removing 
it.
4
  Put the battery “+” pole facing upward, and 
fit the battery into its holder as illustrated.
5
  Slide the battery-chamber cover in the 
direction of arrow until it clicks to secure the 
cover in place.
Specifications
Voltage 
60 V or less 
 
Compatible with center-positive  
 
and center negative polarities
Battery 
Button type 3V lithium battery  
 
(CR1220)
Battery life 
Approx. 10,000 continuous releases 
Dimensions 
Approx. 35.5 × 24.4 × 54.8 mm  
 
(w / h / d)  
 
(1 7/16 × 31/32 × 2 1/4 inches) 
 
(excluding the projecting parts)
Mass 
Approx. 30 g (1.1 oz)
 
(battery not included)
Operating temperature 0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)
Storage temperature  -20 ˚C to +60 ˚C  
 
(-4 ˚F to +140 ˚F)
Included items 
Hot shoe adaptor  
 
FA-HS1AM (1) 
 
(A button type 3V lithium battery  
 
(CR1220) installed)  
 
Set of printed documentation
Design and specifications are subject to change without 
notice.
 is a trademark of Sony Corporation.
1
2
3
4
5
6
1
2
3
4
5
1
2
3
取扱説明書
Operating Instructions
FA-HS1AM
ホットシューアダプター
Hot Shoe Adaptor
Adaptateur de griffe porte-accessoire
© 2008  Sony Corporation   Printed in Japan 
4-112-272-01 (1)
Mode d’emploi
Manual de instrucciones
4
5
English
Before operating the product, please read this manual 
thoroughly and retain it for future reference.
WARNING
To reduce fire or shock hazard, do not expose the unit to 
rain or moisture.
When the lithium battery becomes weak, replace the 
battery with a Sony CR1220 lithium battery. Use of another 
battery may present a risk of fire or explosion.
Battery may explode if mistreated. Do not recharge, 
disassemble or dispose of in fire.
For the State of California, USA only
Perchlorate Material  special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains perchlorate.